Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

 

11

 

 

For great recipes and tips, visit recipes.uniflame.com

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating Sear Burner

First Use

1.Make sure all labels, packaging and protective films have been removed from the grill.

2.Remove manufacturing oils before cooking on this grill for the first time, by operating the grill for at least 15 minutes on “HIGH” with the lid closed. This will “heat clean” the internal parts and dissipate odors.

Lighting

NOTE: Infrared sear burner can be used while main burners are operating.

1.Open lid. Attempting to light the burner with the lid closed may cause an explosion!

2.Make sure there are no obstructions of airflow to the burners. Spiders and insects can nest within and clog the burner / venturi tube at the orifice. A clogged burner tube can lead to a fire beneath the appliance.

3.All control knobs must be in the “OFF” position. (Figure 3)

4.Turn LP gas tank valve to “OPEN”.

5.Push and turn control knob slowly about 1/4 turn counter clockwise until a click is heard. The burner should light. If the burner does not light, repeat up to three times.

6.Hold the knob 3 to 5 seconds to allow gas to reach and light the burner.7.Burner should turn red after 2 to 3 minutes.

8.Turn control knob “OFF” if burner is not lit. Wait 5 minutes and repeat lighting procedure.

Caution: If burner flame goes out during operation, immediately turn the gas “OFF” and open lid to let the gas clear for about 5 minutes before re-lighting.

Turning Off

1.Turn LP gas tank valve to “CLOSED”.

2.Turn all control knobs clockwise to the “OFF” position.

Cooking

Ideal for searing in juices and flavor in food, such as steaks, roasts, and chicken parts.

1.Open lid and ignite the burner per lighting instructions.

2.Close lid and preheat grill on “HIGH”.

3.Wear protective gloves and use long handle tongs to place food onto cooking grids above the burner.

4.Adjust control to desired temperature.

5.Keep an eye on the food to make sure the food does not burn, as it will take a very short time to sear each side of the food. Turn as desired.

6.Turn grill OFF by turning the LP gas tank valve to “CLOSED”. Burn off remaining gas in lines by waiting 15 seconds then turn all burner controls to the “OFF” position. A “poof” sound is normal as the last of the LP gas is burned.

Operating Side Burner

 

NOTE: Side burner can be used while main burners

Figure 7

are operating.

 

Never use side burner as a grill.

 

Lighting

 

1. Open lid. Attempting to light the burner with the

 

lid closed may cause an explosion!

 

Turning Off

1.Turn LP gas tank valve to “CLOSED”.

2.Turn control knob clockwise to the “OFF” position.Note: A “poof” sound is normal as the last of the LP gas is burned.

Cooking

1.Open lid and ignite the burner per lighting instructions in owner’s manual.2.Adjust controls to desired flame height.3.Place pan on center of grid.4.Cook and adjust temperature as needed.

5.Turn grill OFF by turning the LP gas tank valve to “CLOSED”. Burn off remaining gas in lines by waiting 15 seconds then turn all burner controls to the “OFF” position. A “poof” sound is normal as the last of the LP gas is burned.

Operating Infrared Back Burner

First Use

1.Make sure all labels, packaging and protective films have been removed from the grill.

2.Remove manufacturing oils before cooking on this grill for the first time, by operating the grill for at least 15 minutes on “HIGH” with the lid closed. This will “heat clean” the internal parts and dissipate odors.

Lighting

NOTE: Infrared back burner can be used while main burners are operating.

1.Open lid. Attempting to light the burner with the lid closed may cause an explosion!

2.Make sure there are no obstructions of airflow to the burners. Spiders and insects can nest within and clog the burner / venturi tube at the orifice. A clogged burner tube can lead to a fire beneath the appliance.

3.All control knobs must be in the “OFF” position. (Figure 3)

4.Turn LP gas tank valve to “OPEN”.

5.Push and turn control knob slowly about 1/4 turn counter clockwise until a click is heard. The burner should light. If the burner does not light, repeat up to three times.

6.Hold the knob 3 to 5 seconds to allow gas to reach and light the burner.

7.Burner should turn red after 2 to 3 minutes.

8.Turn control knob “OFF” if burner is not lit. Wait 5 minutes and repeat lighting procedure.

Caution: If burner flame goes out during operation, immediately turn the gas “OFF” and open lid to let the gas clear for about 5 minutes before re-lighting.

Turning Off

1.Turn LP gas tank valve to “CLOSED”.

2.Turn all control knobs clockwise to the “OFF” position.

Operating Digital Timer

Count-Up1.Press the ‘Start/Stop’ button. The timer will begin counting up from 0:00.2.Press the ‘Start/Stop’ button. The timer will stop.

2.

Make sure there are no obstructions of airflow to the

 

 

burner. Spiders and insects can nest within and clog

 

 

the burner / venturi tube at the orifice. A clogged

 

 

burner tube can lead to a fire beneath the appliance.

 

3.

Control knob must be in the “OFF” position.

 

 

(Figure 7)

Figure 8

4. Turn LP gas tank valve to “OPEN”.

 

5.

Push and turn control knob counterclockwise to

 

 

“HIGH”.

 

6.

Press the electronic igniter button and hold for 5

 

 

seconds to light burner.

 

7.

If ignition does not occur in 5 seconds, turn burner

 

 

control knob “OFF”, wait 5 minutes, and repeat

 

 

lighting procedure.

 

8.

If igniter does not light burner, use a lit match

 

 

secured with the lighting rod provided to light

 

 

burners manually. Position the lit match near side of

 

Count-Down1.Press the ‘minute’ button to set the desired number of minutes.2.Press the ‘Seconds’ button to set the desired number of seconds.

3.Press the ‘Start/Stop’ button. The timer will begin counting down from the pre-set time.

4.When the timer reaches 0:00 a loud beep will sound for up to 1 minute.

5.To stop the count-down at any time or stop the alarm from sounding, press the ‘Start/Stop’ button.

Light

Press the ‘Light’ button and the LCD will illuminate for 10 seconds. Resetting the timer

Figure 10

Digital Timer
the burner. (Figure 8)

 

 

 

 

Important: Always use the lighting rod provided when

 

Figure 9

 

 

lighting burners with a match.

 

 

 

9. After lighting, observe the burner flame, make sure

 

Flame

Slight

 

all burner ports are lit and flame height matches

 

Yellow

 

 

 

 

illustration. (Figure 9)

 

 

Slight

 

CAUTION: If burner flame goes out

Burner

 

Blue

 

during operation, immediately turn

 

Dark

 

 

 

 

the gas “OFF” and open lid to let the

 

 

Blue

 

gas clear for about 5 minutes before

 

 

 

 

 

 

 

 

re-lighting.

 

 

 

 

If you have stopped the timer during count-up or count-down mode, you can reset it back to 0:00 by pressing and holding the two buttons indicated by the ‘reset’ lines.

Auto Shut-off

In order to increase the battery life, the digital timer will automatically shut off when not in use after 30 seconds. To turn it back on press the ‘Start/Stop’ button