Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

11

For great recipes and tips, visit recipes.uniflame.com.

 

 

 

Troubleshooting

ProblemPossible CausePrevention/Cure
Burner will not light using ignitor

Battery needs to be changed.

Replace the AA battery. (Follow assembly step for inserting

 

 

battery.

 

 

 

 

Wires or electrode covered with cooking residue.

Clean wire and/or electrode with rubbing alcohol.

 

 

 

 

Electrode and burners are wet.

Wipe dry with cloth.

 

 

 

 

Electrode cracked or broken - sparks at crack.

Replace electrode.

 

 

 

 

Wire loose or disconnected.

Reconnect wire or replace electrode/wire assembly.

 

 

 

 

Wire is shorting (sparking) between ignitor and electrode.

Replace ignitor wire/electrode assembly.

 

 

 

 

Bad ignitor.

Replace ignitor.

 

 

 

Burner will not light with match

No gas flow.

Check if LP gas tank is empty. If empty, replace or refill. If LP

 

 

gas tank is not empty, refer to “Sudden drop in gas flow or

 

 

reduced flame height”.

 

 

 

 

Coupling nut and regulator not fully connected.

Turning the coupling nut about one-half to three quarters

 

 

additional turn until solid stop. Tighten by hand only-do not use

 

 

tools.

 

 

 

 

Obstruction of gas flow.

Clear burner tubes. Check for bent or kinked hose.

 

 

 

 

Disengagement of burner to valve.

Reengage burner and valve.

 

 

 

 

Spider webs or insect nest in venturi.

Clean venturi.

 

 

 

 

Burner ports clogged or blocked.

Clean burner ports.

 

 

 

Sudden drop in gas flow or reduced flame height

Out of gas.

Replace or refill LP gas tank.

 

 

 

 

Excess flow; safety device may have been activated.

Turn control knobs to “OFF”. Wait 30 seconds and light grill. If

 

 

flames are still too low, reset the excessive flow safety device

 

 

by turning control knobs “OFF” and LP gas tank valve to

 

 

“CLOSED”. Disconnect regulator. Turn control knobs to “HIGH”.

 

 

Wait 1 minute. Turn control knobs to “OFF”. Reconnect regulator

 

 

and leak check connections. Slowly turn LP gas tank valve

 

 

to “OPEN”. Wait 30 seconds and then light grill per lighting

 

 

instructions.

 

 

 

Irregular flame pattern, flame does not run the full length

Burner ports are clogged or blocked.

Clean burner ports.

of burner.

 

 

 

 

 

Flame is yellow or orange.

New burner may have residual manufacturing oils.

Burn grill for 15 minutes with the lid closed

 

 

 

 

Spider webs or insect nest in venturi

Clean venturi.

 

 

 

 

Food residue, grease or seasoning salt on burner.

Clean burner.

 

 

 

 

Poor alignment of valve to burner venturi.

Assure burner venturi is properly engaged with valve.

 

 

 

Flame blow out

High or gusting winds.

Do not use grill in high winds.

 

 

 

 

Low on LP Gas.

Replace or refill LP gas tank.

 

 

 

 

Excess flow valve tripped.

Refer to “Sudden drop in gas flow or reduced flame height”.

 

 

 

Flare-up

Grease buildup.

Clean grill.

 

 

 

 

Excess fat in meat.

Trim fat from meat before grilling.

 

 

 

 

Excessive cooking temperature.

Adjust (lower) temperature accordingly.

 

 

 

Persistent grease fire.

Grease trapped by food buildup around burner system.

Turn control knobs to “OFF”. Turn LP gas tank valve to

 

 

“CLOSED”. Leave lid in closed position and let fire burn out.

 

 

After grill cools, remove and clean all parts.

 

 

 

Flashback (fire in burner tube(s)).

Burner and/or burner tubes are blocked.

Clean burner and/or burner tubes.

 

 

 

Inside of lid is peeling (like paint peeling).

The lid is stainless steel, not painted.

Baked on grease buildup has turned to carbon and is flaking off.

 

 

Clean thoroughly.

 

 

 

For more assistance please visit us online at www.bluerhino.com or call 1.800.762.1142.