Outdoor LP Gas Barbecue Grill Model No. GTC1000W-C

Operating Instructions

This grill is designed to operate with a one pound 7.75” or 10.6” high disposable / 16.4 oz. or 14.1 oz. propane gas tank (DOT 39 Cylinder). (Figure 1)

DO NOT ATTEMPT TO REFILL ANY ONE POUND (16.4 oz. or 14.1 oz.) PROPANE GAS TANKS!

Connect LP Gas Tank

Only cylinders marked “propane” may be used.Note: Some 1-lb cylinders may form frost when near empty.1.Make sure the control knob is in the (OFF) position. (Figure 2)

2.Lubricate the threads of the regulator with petroleum jelly. Line up threads on LP gas tank with regulator.

3.Insert and rotate LP gas tank clockwise until they fit snugly together. HAND TIGHTEN ONLY. Be careful not to cross threads when screwing in canister.

(Figure 3)

4.Test for leaks, see “Checking for Leaks” section.

Disconnect LP Gas Tank

Figure 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 lb

 

.in 75.7

 

 

1 lb

 

 

 

19,7/

 

 

 

 

 

 

 

 

 

 

 

 

.in6.10

 

 

453 g

 

 

 

 

 

453 g

 

 

 

cm

26,9 /

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.875 in. / 9,8 cm

 

 

 

2.9 in. / 7,4 cm

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 2

Lighting Instructions

Caution: Keep outdoor gas cooking appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

Caution: Do not obstruct the flow of combustion and ventilation air.

Caution: Check and clean burner/ venturi tubes for insects and insect nests. A clogged tube can lead to a fire beneath the grill.

Caution: Attempting to light the burner with the lid closed may cause an explosion.

1.

Make sure all labels, packaging and protective films

 

have been removed from the grill.

2.

Open lid during lighing.

3.

Make sure there are no obstructions of airflow to the

 

gas unit. Spiders and insects can nest within and

 

clog the burner / venturi tube at the orifice.

4. All control knobs must be in the (OFF) position.

 

(Figure 2)

5. Connect LP gas tank per “Connect LP Gas Tank”

 

Figure 6

LP Gas Valve

Burner

with Orifice

venturi

 

pipe

Figure 7a

1. Turn the control knob to the

(OFF) position.

(Figure 2)

Figure 3

2.Rotate LP gas tank counterclockwise until it is loose. (Figure 4)3.Store the LP gas tank in a proper location, per LP gas tank instructions.

Checking for Leaks

Burner Connections1.Make sure the regulator is securely fastened to the burner. (Figure 5a)

If your unit was assembled for you, visually check

Figure 4

the connection between the burner venturi pipe

 

 

and orifice. Make sure the burner venturi pipe fits

 

over the orifice. Please refer to diagram for proper

 

installation. (Figure 6)

 

WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property.

 

instructions.

6.

Select burner to light. Push and turn control knob to

 

(HIGH).

7.

Press the (igniter) repeatedly (3 to 4 times) to light

 

burner.

8.

If ignition does not occur in 5 seconds, turn burner

 

control knob (OFF), wait 5 minutes, and repeat

 

lighting procedure.

9.

If igniter does not light burner, use a lit match to

 

light burner manually. Access the burner through

 

the hole in bottom bowl as indicated. (Figures 7a

 

and 7b)

10. Turn the control knob to (LOW) and position the

 

lit match near side of the burner.

11. After lighting, observe the burner flame. Make sure

 

all burner ports are lit and flame height matches

 

illustration. (Figure 8)

Caution: If burner flame goes out during operation, immediately turn the control knob (OFF) and open lid to let the gas clear for 5 minutes before re-lighting.

Figure 7b

 

Figure 8

Flame

1/2"

12,7 mm

 

1/4"

 

6,4 mm

2.If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for assistance.

Turning Off

1. Turn control knob to the (OFF) position. (Figure 2)

0"

0 mm

Tank/Gas Line Connection

1.Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water.

2.Make sure control knobs are (OFF) position. (Figure 2)

3.Spoon several drops of solution, or use squirt bottle, at all “X” locations. (Figures 5a & 5b)

a.If any bubbles appear remove the LP gas tank and reconnect, making sure the connection is secure.

b.If you continue to see bubbles after several attempts, remove the LP gas tank per “Disconnect LP Gas Tank” instructions, and contact 1.800.762.1142 for assistance.

c.If no bubbles appear after one minute, wipe away solution and proceed.

First Use

1.Make sure all labels, packaging and protective films have been removed from the grill.

2.Remove manufacturing oils before cooking on this grill for the first time by operating the grill

for at least 15 minutes on (HIGH) with the lid closed. This will “heat clean” the internal parts and dissipate odors.

 

Figure 5a

LP Gas Valve

LP Gas

with Orifice

Connection

X

Figure 5b

2.Disconnect LP gas tank per “Disconnect LP Gas Tank” instructions and properly store tank.

Cooking

Caution: Do not leave grill unattended while preheating or burning off food residue on (HIGH). If grill has not been cleaned, a grease fire can occur.

1.Open lid and ignite burner per “Lighting Instructions”.2.Close lid and preheat grill on (HIGH).3.Adjust control knob to desired temperature.

4.Wearing protective gloves lift lid by handle(s) and use long handle tongs to place food onto cooking grids above the lit burners.

5.With lid open or closed, cook until desired internal food temperatures are achieved.

6.Turn grill OFF per “Turning Off” instructions