WARNING

WARNING

CAUTION

WATER PIPING

GAS PIPING

OIL PIPING

MOUNTING THE BURNER

CONNECT TO THE CHIMNEY

Improper installation, adjustment, alteration, service or maintenance can cause serious injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified installer or service agency.

If the information in these instructions is not followed exactly, fire or explosion may result and can cause property damage, personal injury or death.

Do not install on combustible flooring. Minimum clearance to combustible construction is: SIDES: 6”;

BACK: 6”; FRONT: 24”. Install in accordance with all local codes. In the absence of local codes, refer to National Fuel Gas Code and/or NFPA 31 or ANSI Z21.10.1.

Install unions and shut-off valves on both hot and cold water lines. A temperature and pressure (T&P) relief valve has been installed at the factory. Install a discharge line from the relief valve outlet to a suitable drain. Arrange the line without restriction to allow for complete drainage of both the relief valve and line. Do not install a check valve in the cold water line. If backflow preventers or pressure regulators are installed, be sure to make provision for expansion of water when heated by installing either a thermal expansion valve or an expansion tank in the system.

All piping must comply with local codes/ordinances or National Fuel Gas Code & NFPA No. 54

Install a sediment trap or drip leg in the supply line to the burner. Install a union in the gas line adja- cent to and upstream from the control manifold and downstream from the manual main shut-off valve. A 1/8” NPT plugged tapping accessible for test gauge connection must be installed immedi- ately upstream of the gas supply connection to determine the gas supply pressure to the burner.

Install a manual shut-off valve in the gas supply line external to the water heater.

The gas line should be a separate supply direct from the meter to the burner. Use new pipe that is free of cutting burrs and well-supported. Use pipe dope (approved for all gasses) on male threads only.

When pressure testing the gas supply piping system at less that 1/2 psig., close the manual gas shut-off valve to the heater. If test pressures are to exceed 1/2 psig., the water heater and its manu- al shut-off valve must be disconnected from the system. Be sure gas service and meter are ade- quately sized.

All heaters covered by this manual are equipped with two-stage fuel pumps. They require a two pipe system, suction and return. The fuel pumps have the bypass plug installed, which requires a two- pipe system using 5/8” O.D. soft copper tubing.

For gravity flow system (oil supply above the burner), if a one-pipe system is used the bypass plug should be removed. On the larger burners and all dual fuel burners, a two-pipe system is required.

For multiple heater installations, run a separate suction and return line for each heater if possible.

Where the combined lift in feet and horizontal run exceeds 100’, install a booster pump as near to the supply tank as possible. Return lines must be the same diameter as suction lines and extend close to the bottom of the storage tank, but stop slightly above the suction lines. Use a minimum of fittings, making bends in tubing with as large a radius as possible. Always use flared fittings, not compression fittings. If pipe is used instead of tubing, do not connect the burner to the pipe – use copper tubing and form a coil before attaching to the burner.

The burner is shipped separately. Unpack and examine to be sure the unit is in good condition. Install on the water heater using the mounting bolts provided. On larger burners, an additional pedestal is supplied to support the burner. Make sure there are no obstructions in front of the burner and that the burner is not protruding into the combustion area.

Using “L” or “A” type venting, connect the heater to the chimney. Do not reduce the smoke pipe diameter; use the same size smoke pipe as the heater flue pipe. Run a separate connector from the heater to the chimney where possible. If the heater must be joined to another oil appliance breach- ing before going into the chimney, enlarge the existing breaching to accommodate the extra volume of gases from the heater. The entrance into the breaching should be at a 45° angle.

Page 2 Page 4
Page 3
Image 3
Bock Water heaters 150, 200, 250 warranty
Page 2 Page 4

200, 150, 250 specifications

Bock Water Heaters have long been recognized for their reliability and efficiency in providing hot water solutions for both residential and commercial applications. Among their popular offerings are the Bock Water Heaters 200, 150, and 250 models, each designed with unique features and technologies to meet varying demands.

The Bock 200 is designed for smaller households or businesses requiring moderate hot water supply. This model incorporates high-efficiency insulation, which minimizes heat loss, ensuring that water is kept hot for longer periods. It is equipped with a robust burner system that operates on natural gas or propane, providing consistent heating even during peak demand. The Bock 200’s compact design allows for easy installation in limited spaces, making it an ideal choice for urban settings.

Moving to the Bock 150, this model is slightly smaller in capacity but boasts advanced technology that enhances its performance in a variety of installations. Its standout feature is its tankless water heating option, which provides hot water on demand, eliminating the need for a storage tank. This not only saves space but also leads to greater energy efficiency. The Bock 150 is often favored for applications where instantaneous hot water is desired, reducing wait times and energy costs.

The Bock 250 is the flagship model of the series, engineered for larger households or businesses with considerable hot water needs. This model features a high-capacity tank that can provide ample hot water for multiple simultaneous uses, making it perfect for restaurants, hotels, or large families. Its state-of-the-art heating system combines advanced burner technology with efficient heat exchangers, resulting in faster recovery times and lower operational costs. The Bock 250 also incorporates a digital thermostat that allows users to set precise temperatures, contributing to energy savings and enhanced safety.

All three models share key characteristics such as durable construction to withstand rigorous usage and an emphasis on energy efficiency, complying with modern environmental standards. With features like corrosion-resistant tanks and user-friendly controls, Bock Water Heaters continue to be a leading choice for those seeking reliable hot water solutions. The combination of advanced technologies, versatility, and thoughtful design in the Bock 200, 150, and 250 models ensures that there is a suitable option for every hot water requirement. Ultimately, a Bock Water Heater provides peace of mind through quality performance and longevity, making it an investment worth considering for any property.
Top Page Image Contents