Manuals / Bosch Appliances / Household Appliance / Home Security System

Bosch Appliances PLE-10M2-US manual 4.1Connecting inputs, 4.1.1DC supply battery

Models: PLE-10M2-US

1 34

Download 34 pages 39.85 Kb

Page 17

4.1Connecting inputs

Plena Easy Line Mixer Installation and User Instructions Connections and settings

en 17

4 Connections and settings When a 24 VDC battery is connected (typically consisting of two 12 VDC lead-acid batteries in series), the unit will operate on the supplied DC voltage.

4.1Connecting inputs

4.1.1DC supply (battery)

Caution

The connection cable must have an in-line fuse. Use the type of fuse shown in the following figure.

Caution

Make sure the unit is grounded.

The Plena Easy Line Mixer has a 24 VDC input (terminal screw). This input can be used in mobile applications, such as boats where 120 or 230 VAC is not available or in applications that must continue to operate in case of a power failure.

Note

If the backup power system has to comply to the EN54-4 standard or similar standards for backup power and charging speeds, Bosch recommends the PLN-24CH10. The PLN- 24CH10 is a dedicated battery charger and power supply that is fully EN54-4 compliant.

12		FUSE
12	VDC
	VDC
	12	VDC
		VDC

figure 4.1: Connecting a DC power supply

Bosch Security Systems 2008-04 PLE-10M2-US en

Image 17

Bosch Appliances PLE-10M2-US manual 4.1Connecting inputs, 4.1.1DC supply battery

Contents

PLE-10M2-US Plena Easy Line Mixeren Important safeguardsAlerts on the apparatus Bosch Security Systems 2008-04 PLE-10M2-USenWhen the power-supplycord or plug is damaged en Table of contents en 1.1Purpose Introduction1.2Digital document 1.3Intended audience1.7Conversion tables 2Description 2.2Contents of box2.1The Plena product range 2.3The Plena Easy Line MixerBosch Security Systems 2008-04 PLE-10M2-USen 24 VDC power from the 24 V inputen 2.4.2Plena PLE-WP2Z3Swall panel 2.4Controls, connectors and indicators2.4.1Front panel en 2.4.3Rear panelThe unit must be grounded Bosch Security Systems 2008-04 PLE-10M2-USenfigure 2.3 Rear panel power 40VARated input Line fuseBosch Security Systems 2008-04 PLE-10M2-USen Intentionally left blanken 3.2Install unit in rack optional 3Installation3.3Check settings/connections 3.1Unpack unitBosch Security Systems 2008-04 PLE-10M2-USen Intentionally left blanken 4.1.1DC supply battery 4.1Connecting inputsBosch Security Systems 2008-04 PLE-10M2-USen 4.1.2Priority microphone inputen figure 4.3 Connecting microphone inputs 4.1.3Secondary microphone input4.1.4Additional microphones inputs 3 through 4.1.5.1Connecting 70 Volt input signal 4.1.5Emergency inputsen Bosch Security Systems 2008-04 PLE-10M2-USen4.1.5.2Connecting telephone lines figure 4.6 Connecting music source inputs 4.1.6Music source inputs4.2.1Zone 1 and 4.2Connecting outputs4.2.2Call active contact 4.2.3Music only4.3.1Rear panel settings 4.3Unit settingsen 4.3.2Pin settings and labeling 5.1.2Switch off 5.1Switch on and off5.1.1Switch on 5Operation5.2Microphone/line controls 5.3.2Volume control5.3Music controls 5.4Tone control5.5.1Zone selection 5.5.2Master volume control5.5Output controls Bosch Security Systems 2008-04 PLE-10M2-USen Intentionally left blanken 6.1.1Mains power supply 6Technical data6.1.2Battery power supply 6.1Electrical6.3Environmental 6.2Mechanical6.1.6Music inputs 6.1.7Emergency / telephone 1Page Bosch Security Systems B.V For more information visitData subject to change without notice 2008-04 PLE-10M2-USen