Operating Tips

BM 2610944508 11-06 12/1/06 3:29 PM Page 13

TETHER HOOK

The purpose of the tether hook is to secure the tool when working on ladders, scaffolding, or elevated heights to prevent the tool from hitting the ground if accidentally

dropped. For best results, it is recommended to use 1/4" braided nylon rope or similar material.

You will extend the life of your bits and do neater work if you always put the bit in contact with the work before pulling the trigger. During the operation, hold the tool firmly and exert light, steady pressure. Too much pressure at low speed will stall the tool. Too little pressure will keep the bit from cutting and cause excess friction by sliding over the surface. This can be damaging to both tool and bit.

DRILLING WITH VARIABLE SPEED

The trigger controlled variable speed feature will eliminate the need for center punches in hard materials. The variable speed trigger allows you to slowly increase RPM. By using a slow starting speed, you are able to keep the bit from “wandering”. You can increase the speed as the bit “bites” into the work by squeezing the trigger.

DRIVING WITH VARIABLE SPEED

Variable speed drills will double as a power screwdriver by using a screwdriver bit in the drill mode. The technique is to start slowly, increasing the speed as the screw runs down. Set the screw snugly by slowing to a stop. Prior to driving screws, pilot and clearance holes should be drilled.

FASTENING WITH SCREWS

This procedure shown in (Fig. 8) will enable you to fasten materials together with your

Screw drills are available for screw sizes No. 6, 8, 10 and 12.

Cordless Drill/Screwdriver without stripping, splitting or separating the material.

First, clamp the pieces together and drill the first hole 2/3 the diameter of the screw. If the material is soft, drill only 2/3 the proper length. If it is hard, drill the entire length.

Second, unclamp the pieces and drill the second hole the same diameter as the screw shank in the first or top piece of wood.

Third, if flat head screw is used, countersink the hole to make the screw flush with the surface. Then, simply apply even pressure when driving the screw. The screw shank clearance hole in the first piece allows the screw head to pull the pieces tightly together.

FASTENING WITH

SCREWS

1.Drill 2/3 diameter and 2/3 of screw length for soft materials, full length for hard materials.

Screw

Apply a slight even pressure when driving screws.

2.Drill same diameter as screw shank.

3.Countersink same diameter as screw head.

Adjustable

Screw

Drill

The adjustable screw drill accessory will do all of these operations quickly and easily.

FIG. 8

DRILL BITS

Always inspect drill bits for excessive wear. Use only bits that are sharp and in good condition.

TWIST BITS: Available with straight and reduced shanks for wood and light duty metal drilling. High speed bits cut faster and last longer on hard materials.

CARBIDE TIPPED BITS: Used for drilling stone, concrete, plaster, cement and other

unusually hard nonmetals. Use continuous heavy feed pressure when employing carbide tip bits.

DRILLING WOOD

Be certain workpiece is clamped or anchored firmly. Always apply pressure in a straight line with the drill bit. Maintain enough pressure to keep the drill “biting”.

-13-

18636-03, 18636, 18636-01, 18636-02 specifications

Bosch Power Tools is synonymous with innovation and reliability, and their series of cordless drills, including models 18636-02, 18636-01, 18636, and 18636-03, exemplify these attributes. Designed for both professional tradespeople and DIY enthusiasts, these models are engineered to deliver exceptional performance in a variety of applications.

One of the main features of these Bosch drills is their powerful motor that provides an impressive torque output. This ensures that users can tackle a wide range of tasks, from drilling through tough materials to driving screws with precision. The models are equipped with a two-speed transmission, allowing users to switch between high torque for heavy-duty tasks and high speed for quick drilling, enhancing versatility.

The cordless design is another significant characteristic. Powered by advanced lithium-ion batteries, these models offer increased run time and reduced charging time. This technology ensures that tools remain lightweight while providing consistent power, enabling users to work without interruptions. Depending on the model, the battery capacity varies but consistently provides ample performance for extended tasks.

Ergonomics is a key consideration in the design of the 18636 series. The tools come with rubberized grips that enhance comfort and reduce user fatigue during prolonged use. The balanced design of these drills adds to their ease of handling, making them suitable for both professional applications and home improvement projects.

In terms of durability, Bosch has incorporated robust materials in the construction of these drills. They are designed to withstand the rigors of job site use, featuring shock-resistant housings that protect internal components from damage. Additionally, some models include advanced electronics that enable features like electronic brake and overload protection, further enhancing longevity.

User-friendly features are prevalent in this lineup, including LED work lights that illuminate dark work areas, and keyless chuck systems that allow for fast and easy bit changes. The models also frequently feature a built-in battery life indicator, enabling users to monitor power levels and avoid unexpected downtime.

In conclusion, the Bosch Power Tools 18636-02, 18636-01, 18636, and 18636-03 represent a commitment to quality, performance, and user convenience. With their powerful motors, efficient battery technology, ergonomic design, and durable construction, these drills are apt for a multitude of tasks, making them valuable assets in any toolbox. These tools demonstrate Bosch’s dedication to delivering cutting-edge solutions that meet the needs of today's demanding work environments.

Bosch Power Tools 18636-02, 18636-03, 18636-01 manual Operating Tips

Models: 18636-03 18636 18636-01 18636-02