Installation

Instructions

WARNING

Always turn off the amplifier or receiver when connecting speakers or any other components to the system.

NOTE

This manual assumes the installer possesses skill in the proper use of hand and power tools, knowledge of local building and fire codes, and a familiarity with the environment behind the wall or ceiling in which the speakers will be installed.

Tools You’ll Need

1.A utility knife, jig saw, or other tool for cutting the required hole in the mounting surface.

2.A #2 Phillips screwdriver.

3.A wire cutter or stripper for prepar- ing the speaker wires.

4.A pencil.

Retrofit Installations

1.Mark the outline of the installation hole using the supplied template. Make a small hole at the center of the speaker location. Insert a long, bent piece of wire and rotate to confirm that there are no obstruc- tions behind the chosen location.

2.Cut the installation hole.

3.Run the wire from the amplifier location to the cutout. Allow for an extra foot of wire at the cutout.

Instrucciones de montaje

AVISO

Apague siempre el amplificador o el receptor al conectar altavoces o cualquier otro componente al sistema.

NOTA

En este manual se presupone que el instalador posee habilidad en el mane- jo de herramientas manuales y eléctric- as, conocimiento sobre los códigos vigentes de construcción local y normas sobre incendios y que está familiariza- do con el entorno tras el muro o techo en los que se instalarán los altavoces.

Herramientas necesarias

1.Una navaja multiusos, una sierra caladora u otra herramienta para cortar el agujero adecuado en la superficie de montaje.

2.Un destornillador de estrella o cruz del número 2.

3.Un cortador de alambre o un pelacables para preparar el cablea- do de los altavoces.

4.Un lápiz.

Instalaciones para el montaje trasero

1.Marque el contorno del agujero con la plantilla suministrada. Haga un pequeño agujero en el centro de la ubicación del altavoz. Meta un alam- bre curvado y dele vueltas para ase- gurarse de que no hay obstáculos traseros en la posición elegida.

2.Corte el agujero para la instalación.

3.Tienda el cable desde el amplificador hasta el final. Corte a 30 cm más de lo necesario.

Instructions d’installation

AVERTISSEMENT

Débranchez toujours l’amplificateur ou le récepteur avant de connecter les enceintes ou tout autre composant du système.

REMARQUE

Ce manuel suppose que l’installateur sait utiliser les outils à main et à moteur nécessaires à l’installation, qu’il connaît la réglementation en vigueur sur la construction et l’incendie, et qu’il sait exactement ce qui se trouve derrière les murs ou les plafonds sur lesquels les enceintes seront installées.

Outils nécessaires

1.Un couteau, une scie à découper ou tout autre outil capable de découper l’orifice nécessaire dans la surface de montage.

2.Un tournevis cruciforme No. 2.

3.Une pince coupante ou à dénuder pour préparer les fils des enceintes.

4.Un crayon noir

Installations améliorées

1.Tracez le contour de l’orifice d’in- stallation en utilisant le gabarit fourni. Faites un petit trou au centre de l’endroit où sera placée l’en- ceinte. Insérez-y un grand morceau de câble replié, et faites tourner celui-ci afin de vous assurer qu’il n’existe aucun obstacle derrière l’endroit choisi.

2.Découpez l’orifice d’installation.

3.Amenez le câble de l’ampli à l’ori- fice que vous venez de découper, en prévoyant 30 cm de câble sup- plémentaire.

Installationsan- weisungen

ACHTUNG

Den Verstärker oder Empfänger immer abstellen, wenn Lautsprecher oder andere Komponenten an das System angeschlossen werden.

HINWEIS

Dieses Handbuch setzt voraus, dass der Installateur im Umgang mit Hand- und Elektrowerkzeugen versiert ist, die örtlichen Bau- und Brandschutz- vorschriften kennt und weiß, wo und welche Leitungen in der Wand bzw. hin- ter der Wandverkleidung verlaufen, in der die Lautsprecher montiert werden sollen.

Benötigte Werkzeuge

1.Ein Exaktormesser, eine Stichsäge oder anderes Werkzeug zum Ausschneiden des notwendigen Lochs aus der Montagefläche.

2.Einen Kreuzschlitz-Schraubendreher, Größe 2.

3.Eine Drahtzange oder einen Drahtstripper zur Vorbereitung der Lautsprecherkabel.

4.Einen Bleistift.

Einbau in eine fertige Fläche

1.Den Umriss des Installationslochs mit der mitgelieferten Maske anze- ichnen. In der Mitte der auszuschneidenden Fläche ein kleines Loch erzeugen. Ein langes Stück gebogenen Drahts in das Loch einschieben, um zu prüfen, dass hinter der gewählten Stelle keine Hindernisse vorhanden sind.

2.Das Montageloch schneiden.

3.Das Kabel vom Verstärker zum eben erzeugten Ausschnitt verlegen. An der Ausschnittstelle etwa 30 cm extra Kabellänge vorsehen.

– 8 –

Page 7 Page 9
Page 8
Image 8
Boston Acoustics HSi N640T2, HSi N740 Installation Instructions, Instrucciones de montaje, Instructions d’installation
Page 7 Page 9

HSi N740, HSi N640T2 specifications

Boston Acoustics has long been synonymous with high-quality audio, and their HSi line of speakers, particularly the HSi N640T2 and HSi N740, exemplifies this tradition. These speakers are designed to deliver exceptional sound quality in a stylish form, making them ideal for both audiophiles and casual listeners alike.

The HSi N640T2 is a versatile 6.5-inch two-way speaker system that is perfect for various listening environments. One of its standout features is its innovative WaveGuide technology, which enhances the speaker's dispersion characteristics and creates a more expansive soundstage. This ensures that listeners experience a rich, immersive audio experience, no matter where they are positioned in the room. The HSi N640T2 utilizes a high-performance 6.5-inch polypropylene woofer that delivers robust bass response and clarity, while the 1-inch silk dome tweeter ensures crisp high frequencies, making every note clear and detailed.

On the other hand, the HSi N740 is a powerful 7-inch two-way speaker system that takes performance to the next level. This model is equipped with a larger woofer, which allows for deeper bass response and increased overall output. The HSi N740 also features Boston Acoustics' proprietary BassTrac circuitry, which prevents distortion at high volume levels and provides clean, undistorted bass across various listening levels. Another notable characteristic of the HSi N740 is its frequency response range, which extends from 37 Hz to 25 kHz, ensuring that all audio frequencies are reproduced accurately.

Both models boast a sleek, low-profile design that allows them to blend seamlessly into any décor. Their robust cabinet construction helps reduce unwanted vibrations and resonance, ensuring that the sound remains pure and true to the original recording. Additionally, the HSi series is designed for easy installation, making them a popular choice for both custom installations and simple home setups.

In summary, the Boston Acoustics HSi N640T2 and HSi N740 speakers highlight the brand's commitment to delivering high-quality audio with innovative technology. With features designed to optimize sound performance and a design that complements modern living spaces, these speakers are suitable for anyone looking to enhance their audio experience. Whether for music, movies, or gaming, the HSi N640T2 and HSi N740 provide listeners with a listening experience that truly resonates.
Top Page Image Contents