Installation Instructions

Roller Bar Mower Kit

Leveling The Mower

If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as speci- fied in Checking Tire Pressure.

SIDE-TO-SIDE LEVELING

1.With the mower installed, place the tractor on a smooth, level surface such as a concrete floor. Turn the front wheels straight forward.

2.Check for bent blades and replace if necessary.

3.Place the mower in mid-cut position. Arrange the out- side mower blades so that they are pointing from side-to-side.

4.Measure the distance between the outside tips of each blade and the ground. If there is more than 1/8” (3mm) difference between the measurements on each side, proceed to step 5. If the difference is 1/8” (3mm) or less, proceed to step 6.

ECCENTRIC NUT MODELS

5.See Figure 8. Loosen the outside nut (A). Turn the eccentric nut (B) to raise or lower left-hand side of mower. When mower is level, hold the eccentric nut while tightening the outside nut.

NOTE: 44”, 50”, & 54” Mowers. When using a turbo col- lection system, raise the discharge side of the mower approximately 1/4” (6mm) to compensate for turbo assembly weight. Check the level of the cut grass and adjust the 1/4” (6mm) measurement as necessary for a smooth, even cut.

FRONT-TO-BACK LEVELING

NOTE: 54” mowers have two adjustment rods that should be adjusted simultaneously.

6.Arrange the blades so they face front-to-back.

7.Measure the distance from the ground to the front tip of the center blade, and from the ground to rear tips of left-hand and right-hand blades.

Front tip of the center blade should be 1/4" (6mm) higher than rear tips of left-hand and right-hand blades. If not, proceed with steps 8 - 9.

8.To raise front of mower deck, loosen front nut (B) and turn rear nut (A, Figure 10) against bracket. To lower front of mower deck, loosen rear nut (A) and the bracket will move backwards to lengthen rod.

A

B

Figure 8. Leveling The Mower Side-to-Side Eccentric

Nut Models

 

A. Outside Nut

B. Eccentric Nut

A

B

Figure 10. Front to Back Leveling

A. Rear Nut

B. Front Nut

9.Re-check the blade measurement then tighten the front nut (B) against the bracket to secure.

Form No. 1727716

Revision:02

TP 200-4144-02-SK-SMAN

MANUFACTURING, INC .

Briggs & Stratton Yard Power Products Group

 

500 N Spring Street / PO Box 997

Copyright © 2007 Briggs & Stratton Corporation

Milwaukee, WI USA. All Rights Reserved

Port Washington, WI 53074-0997 USA

 

6

Page 6
Image 6
Briggs & Stratton 1687077 installation instructions Leveling The Mower, Front to Back Leveling Rear Nut Front Nut

1687077 specifications

The Briggs & Stratton 1687077 is a powerful small engine renowned for its reliability and efficiency. This model is predominantly utilized in outdoor power equipment such as lawn mowers, generators, and pressure washers, making it a versatile choice for both commercial and residential users.

At the heart of the 1687077 is its robust design, featuring a 4-stroke, single-cylinder engine that delivers substantial performance. The engine is known to produce around 6.75 to 7.5 horsepower, depending on the specific application. This power output ensures that the engine can handle a variety of tasks, from cutting grass to generating electricity, with exceptional ease.

One of the standout features of the 1687077 is its innovative overhead valve (OHV) technology. This design improves airflow to the combustion chamber, resulting in better fuel efficiency, reduced emissions, and enhanced performance over conventional side-valve configurations. This technological advancement not only helps in conserving fuel but also leads to a cleaner engine operation.

The engine is also equipped with a reliable starter system, which simplifies the starting procedure, even in cold weather. The recoil starting mechanism is straightforward and requires little effort, making it user-friendly for all skill levels. Additionally, the inclusion of an automatic choke system enhances the starting process, reducing the chances of flooding the engine during initial startup.

Durability is another prime characteristic of the Briggs & Stratton 1687077. The engine utilizes a quality cast iron sleeve, which extends its lifespan and improves protection against wear and tear. This feature is particularly beneficial for users who rely on their equipment for frequent and heavy-duty use. Moreover, the engine's design minimizes oil consumption, further contributing to its longevity.

To ensure ease of maintenance, the 1687077 has been built with accessibility in mind. Its components are designed for straightforward servicing, allowing users to perform routine maintenance tasks with minimal hassle. This includes changing the oil, replacing the air filter, and inspecting spark plugs.

Overall, the Briggs & Stratton 1687077 stands out as a reliable engine with a blend of power, efficiency, and longevity. Its advanced technologies and user-centric design make it an excellent choice for anyone in need of a dependable small engine for outdoor applications. Whether for professional use or as a part of a homeowner's toolset, the 1687077 is engineered to meet a variety of demands while delivering consistent performance.