Generator AC Connection System

A single-phase, three-wire AC connection system is used in the home generator. The stator assembly consists of a pair of stationary windings with two leads brought out of each winding. The junction of leads T2 and T3 forms the neutral lead, as shown schematically and as wiring diagram below. A complete schematic and wiring diagram can be found later in this manual.

NOTE: Neutral is not bonded to ground at generator.

Power
	Neutral

Winding	120 V
Winding
	120 V
	Circuit
	Breaker

	T4		240 V
	T1		240 V
	T1
Neutral	T4	T1	Ground
		Circuit
N		Breaker	G

		Line 1		Line 2		Ground
Neutral

To Transfer Switch

Control Waterter

Board Heater

10 A

240 VAC

ToToTTransfer Switch

UtilitilityFuse Connection

Grounding the Generator

Ground the home generator per applicable codes, standards and regulations. There are two generator GND lug locations. The one inside the alternator junction box next to the circuit breaker is the primary lug and should meet most applications. The second generator GND lug is located on the frame below the generator circuit breaker cover, and should ONLY be used for a ground rod located at the generator, if required by local codes. See Controls for location.

Utility Circuit Connection

“240V Utility” leads must be routed in conduit. The

“240V Utility” leads deliver power to the generator’s circuit board and water heater. This power also charges the battery. When power on these leads is lost, the generator will start.

Using installer-supplied minimum 300V, 14 AWG copper wire, connect each ten-amp fuse terminal in the alternator junction box to the ten-amp fuse terminals in the automatic transfer switch.

Fault Detection System

The generator may have to run for long periods of time with no operator present. For that reason, the system is equipped with sensors that automatically shut down the generator in the event of potentially damaging conditions, such as low oil pressure, high water temperature, over speed, and other conditions. Refer to Fault Detection System in the Operator’s Manual for more detailed information.

The owner will use the remote LED indicator to observe the status of the home generator system. Consult with the owner for a convenient location.

To install the remote LED indicator:

1.Push the LED through the mounting plate from the front until it snaps in place.

IMPORTANT: The LED is polarity sensitive.

2.Using provided 10 pole connector and installer-supplied minimum 18AWG wire, connect the remote LED to the generator control board +LED and GND connection. Use wire nuts to attach wire to LED leads.

3.Attach mounting plate to installer-supplied electrical box.

NOTE: Locate the electrical box in an area visible by the home owner such as near a garage door opener or security control panel.

14	BRIGGSandSTRATTON.COM

45000 specifications

The Briggs & Stratton 45000 is a powerful generator that stands out in the realm of portable power solutions. Designed for a variety of applications, it is an ideal choice for homeowners, outdoor enthusiasts, and professionals alike. With a robust engine and advanced features, it ensures a reliable source of electricity when you need it most.

One of the key features of the Briggs & Stratton 45000 is its impressive power output. It provides starting watts of 4,500 and running watts of 3,600, making it suitable for powering essential appliances during outages or for running tools on job sites. This generator is equipped with a durable 306cc engine that utilizes a reliable overhead valve (OHV) design for enhanced performance and efficiency. This engine type ensures lower oil consumption, reduced emissions, and quieter operation compared to traditional engines.

The generator's lightweight design and integrated handle make it highly portable. Weighing approximately 107 pounds, it is easy to transport, allowing for seamless movement from one location to another. The rugged wheels provide excellent maneuverability over uneven terrain, making it a perfect companion for camping trips, tailgating events, and outdoor projects.

Another notable feature of the Briggs & Stratton 45000 is its user-friendly control panel. Equipped with multiple 120V AC outlets, it allows users to connect various devices and appliances simultaneously. The addition of a USB port facilitates charging smartphones and tablets, catering to the modern user’s needs. The generator also includes a built-in circuit breaker to protect against overloads, ensuring the safety of connected devices.

Advanced technologies further enhance the performance and usability of the Briggs & Stratton 45000. For instance, it features a digital display that keeps users informed about the voltage output and running hours. An automatic shutoff function prevents engine damage by alerting users when oil levels are low. Additionally, the generator incorporates a pressurized lubrication system that enhances longevity and minimizes wear and tear.

To top it off, the Briggs & Stratton 45000 meets various safety standards, providing peace of mind for everyone using it. With all these features combined, the Briggs & Stratton 45000 stands as a reliable and efficient portable generator that meets the diverse power needs of users across various settings. Whether at home, on the job, or enjoying the great outdoors, this generator can be counted on to deliver dependable performance.

Briggs & Stratton 45000 system manual Generator AC Connection System, Grounding the Generator

Models: 45000