Troubleshooting, Adjustment & Service

RIDER TROUBLESHOOTING CONTINUED.

 

PROBLEM

CAUSE

REMEDY

 

 

Engine runs, but rider will

1.

Hydraulic release valve(s)

1.

Turn valve(s) clockwise to close.

 

 

not drive.

 

in “open” position.

 

 

 

 

 

2.

Belt is broken.

2.

See Drive Belt Replacement.

 

 

 

3.

Drive belt slips.

3.

See problem and cause below.

 

 

 

4.

Brake is not fully released.

4.

See authorized service dealer

 

 

 

 

 

 

 

 

 

Rider drive belt slips.

1.

Pulleys or belt greasy or oily.

1.

Clean as required.

 

 

 

2.

Belt stretched or worn.

2.

Replace belt.

 

 

 

 

 

 

 

 

 

Brake will not hold.

1.

Brake is incorrectly adjusted.

1.

See Brake Adjustment.

 

 

 

2.

Brake caliper pads worn.

2.

Replace with new brake pads.

 

 

 

 

 

 

 

 

Rider steers or handles poorly.

1.

Steering linkage is loose.

1. Check and tighten any loose connections.

 

 

 

2.

Improper tire inflation.

2.

See Regular Maintenance Section.

 

TROUBLESHOOTING THE MOWER

 

PROBLEM

CAUSE

 

 

REMEDY

 

 

Mower will not raise.

1.

Lift linkage not properly attached

1.

See authorized service dealer for repair.

 

 

 

 

or damaged.

 

 

 

 

 

 

Reproduction

 

 

Engine stalls easily with

1.

 

for

1.

Set to full throttle.

 

 

Engine speed too slow.

 

 

mower engaged.

2.

Ground speed t

fast.

2.

Decrease Ground Speed.

 

 

 

3.

Cutting height set t l w.

3.

Cut tall grass at maximum cutting

 

 

 

 

 

 

 

 

he ght during first pass.

 

 

 

4.

Discharge chu e jamming

4.

Cut grass with discharge pointing toward

 

 

 

 

with cut grass.

 

 

previously cut area.

 

 

 

 

 

 

 

 

 

Excessive mower vibration.

1.

Blade m un ing bolts are loose.

1.

Tighten to 70 ft.lbs. (94 N.m.).

 

 

 

2.

M wer blades, arbors,

2.

Check and replace as necessary.

 

 

 

 

r pulleys are bent.

 

 

 

 

 

3.

Mower blades are out

3.

Remove, sharpen, and balance blades.

 

 

 

 

of balance.

 

 

See Maintenance Section.

 

 

 

Not4. Belt installed inc ectly.

4.

Reinstall Correctly.

 

 

Excessive belt wear or breakage.

1.

Bent or ough

ulleys.

1.

Repair or replace.

 

 

 

2.

Using incorrect belt.

2.

Replace with correct belt.

 

 

 

 

 

 

 

 

 

 

Mower drive belt slips

1.

Idl r

ull y s ring broken or not

1.

Repair or replace as needed.

 

 

or fails to drive.

 

prop

rly attached.

 

 

 

 

 

2.

Mow

r drive belt broken.

2.

Replace drive belt.

 

34

www.ferrisindustries.com