1. Assembling and using the stroller
(The stroller seat unit is intended for children six months or older and up to 40 lbs or 18 kg)
1a
1b
1c
1d1e
Release storage latch.
Tip: To avoid difficulty in attaching rear wheels, keep storage latch from resting above
Hold handle and lift upwards until stroller frame is fully extended and clicks into position.
Push front
When properly fitted, the screw head on the front
Pull down gently on the wheel to ensure it is fully engaged.
Repeat process for remaining front wheel.
Push rear wheel into rear- wheel axle housing. Wheel is fitted when you hear a positive “click.” Repeat process for remaining rear wheel.
To ensure proper installation, use arrow imprinted on outer wall of tires as a visual guide. When stroller is pushed forward, the front of the arrows should point and move in the same direction in which the wheels are turning.
Check wheels are fully engaged by gently trying to pull them out.
Adjust handle height by simultaneously pressing buttons on inside of handle on both sides and rotating padded portion of handle into desired position.
Check stroller frame is ready for use by pressing down on handle - stroller frame should not collapse.
WARNING: Ensure stroller- frame is locked before use.
1i | 1j | 1k | 1l | 1m |
Rotate seating unit downward until seat locking clips fully engage with the opposite bar.
WARNING: Check that
To attach arm bar, align arm- bar moldings with plastic tabs on seating unit and slide both
Ensure arm bar is securely in place by gently pulling on it.
To remove arm bar, remove hood (if fitted) and slide both
WARNING: NEVER lift stroller by the arm bar or hood as they may disengage. If needed, lift stroller by handle and stroller frame.
To fit hood, align moldings with plastic tabs on arm bar and slide down until fully engaged.
Hood can be fitted without arm bar by aligning hood moldings with plastic tabs on seat unit and sliding down until fully engaged.
To open hood, pull front of hood forward then push hood hinges down on both sides.
To close hood, lift up hood hinges on both sides and push front of hood back.
To adjust the angle of the seating unit, squeeze recline adjuster lever at top of seating unit, then adjust seating unit to desired position.
IMPORTANT: Use harness at all times. Always support back of stroller seat when reclining it.
2. Folding and storing the stroller
2a | 2b | 2c | 2d |
2e
1f
1g
1h
Push down on parking brake To unlock swivel wheels, pull To install seat unit (forward or
lever to lock brakes. To release front wheel swivel lock lever up rear facing), store infant carrier
brake, lift parking brake lever. on each front wheel. To lock, attachment bar. (See section 3.)
align wheels to rear of front leg Slide hooks at foot end of seat
IMPORTANT: Always engage and push lock down.unit onto stroller support bar
parking brake when fitting seatuntil hooks are fully engaged
unit.with support bar.
WARNING: Always remove child from seat unit prior to installation, removal or change of seat direction.
D
B | B |
C
A 
1n D
1o
To secure child in harness, slide each waist clip (A) into buckle (C) until prongs snap into position. Clip harness belt hooks (B) onto waist belt clip. Carefully adjust harness by pulling sliders (D) until desired fit is achieved in waist, shoulder and crotch straps.
WARNING: Always use crotch strap in combination with waist belt. Fasten harness when not in use to prevent it from becoming trapped when folding the stroller.
To raise shoulder harness height, pull harness straps through harness height adjuster so that they lay flat on top of the harness height adjusters.
To lower shoulder harness height, thread harness straps through harness height adjuster so they lay flat against the seat back, under the harness height adjuster.
3. Using as a travel system
Britax Companion® Click and Go™
3a | 3b | 3c |
To remove seating unit, apply parking brake. Release both locking clips from support bar by lifting and holding both seat- locking clips.
Raise rear of seating unit clear of support bar, then slide seat unit forward and out of the stroller frame.
WARNING: Always remove child from the seat before installation, removal, change of seat direction or folding.
Tip: Stroller frame may also be folded with seating unit attached.
Stand at rear of stroller frame, pull both release latches and twist right hand latch in the direction of arrow marked on release latch.
For more compact storage, fold handle down. (See diagram 1e.)
Push handle down, allowing stroller frame to fold until it moves into a fully folded position. Ensure storage latch is closed.
For more compact storage, remove front swivel wheels. Slide front wheel locking button toward the middle of the stroller, then pull corresponding swivel wheel out.
To remove rear wheels, press rear wheel locking button and pull corresponding rear wheel out. Repeat process for remaining rear wheel.
Remove seat unit. (See diagram 2a.) Swing carrier attachment bar (hanging near front of the storage basket) forward until it engages with the stops affixed to the front of the stroller frame.
IMPORTANT: When using as a travel system, always remove infant carrier prior to folding of stroller.
WARNING: Apply parking brake when attaching or removing your infant carrier. (See diagram 1f.)
Lower the carrier rear facing with attachment hooks aligned with attachment bar. Press carrier onto attachment bar until a positive click is heard.
IMPORTANT: To ensure proper installation, pull up on carrier by the handle (in carrying position) to verify both attachment hooks are engaged with the attachment bar.
WARNING: Check that carrier attachment bar is correctly engaged before use.
WARNING: Ensure your child is harnessed at all times.
WARNING: NEVER lift the stroller by the infant carrier.
To remove carrier, squeeze release lever on back of seat while lifting carrier from stroller.
Pull carrier attachment bar away from front stops and swing it back so that it rests against the front of the storage basket.
