MODELS QP230BC • QP230BL • QP230SS • QP230WW QP236BC • QP236BL • QP236SS • QP236WW QP242BC • QP242BL • QP242SS • QP242WW
Page 3
FUSE |
|
FUSE | RANGE HOOD CONTROL BOARD |
The Range Hood Control Board contains a Fuse to protect the controls from power surges. If the fuse has opened (blown), the green fan setting or light setting indicators will not operate properly when the fan or light buttons are pressed, and the fan and lights will not turn on.
A new fuse can be purchased at your local electronic supply store. Use an 8A, 120V, 5 mm diameter, 20 mm long,
To replace the fuse (by qualified person(s):
1.Disconnect power at service entrance.
2.Remove filters and bottom pan.
3.Remove and inspect fuse. If it is not open (blown), additional diagnostics are needed.
PREPARE HOOD LOCATION
ROOF CAP | 3¼" X 10" or |
| 7" ROUND DUCT |
| (For vertical |
| discharge) |
2 | Use the proper diagram below, for placement of ductwork |
| and electrical cutout in cabinet or wall. For a |
| installation, DO NOT cut a duct access hole. |
|
|
|
|
|
|
|
|
| 3¼” X 10” | ||
HOOD MOUNTING SCREWS (5) | VERTICAL DUCTING | ||||||||||
|
|
| |||||||||
11 | 5/8" (30" hood) | 11 | 5/8" | (30" hood) | |||||||
|
| 14 | 5/8" (36" hood) |
|
|
| 14 | 5/8" (36" hood) |
|
| |
|
|
|
| ||||||||
17 | 5/8" (42" hood) | 17 | 5/8" (42" hood) | ||||||||
|
| CABINET FRONT |
|
|
|
|
|
| |||
CABINET | * 67/8" |
|
|
|
BOTTOM |
|
|
| |
5¼" | 5¼" | 11" | 21/8" | 107/8" |
VERTICAL DUCT | 25/8" | |||
4½" ¾" |
|
|
| |
ACCESS HOLE |
|
|
| |
|
|
|
|
| ELECTRICAL | |
WOOD SHIMS | CENTER | ACCESS HOLE | ||||
(in cabinet bottom) | ||||||
LINE | ||||||
cabinets only) |
| |||||
|
|
|
| |||
WOOD SHIMS |
|
|
| 3¼” X 10” | |
|
| HORIZONTAL DUCTING | |||
|
| ||||
|
|
|
| ||
cabinets only) | CABINET FRONT | 13/8" | |||
|
|
|
|
| 3/8" |
CABINET 4" |
| * |
|
| |
HORIZONTAL DUCT |
| ||||
ACCESS HOLE |
|
| |||
BOTTOM | 5¼" | 5¼" |
| ||
|
|
|
| 67/8" | |
11 | 5/8" (30" hood) | 11 | 5/8" (30" hood) | ||
14 | 5/8" (36" hood) | 14 | 5/8" (36" hood) | ||
17 | 5/8" (42" hood) | 17 | 5/8" (42" hood) | ||
HOOD | CENTER |
| ELECTRICAL | ||
MOUNTING |
| ||||
SCREWS (5) | LINE |
| ACCESS HOLE | ||
|
|
| (in wall) | ||
|
|
|
|
| |
SOFFIT |
CABINET |
HOOD |
24" - 30" ABOVE |
COOKING SURFACE |
HOUSE WIRING (Top or Back of hood)
WALL CAP
3¼" X 10" DUCT
(For horizontal discharge)
HOOD MOUNTING SCREWS (5) |
|
|
| ||||||||||||||||||||||
|
| DUCTING | |||||||||||||||||||||||
11 | 5/8" (30" hood) | 11 | 5/8" (30" hood) |
|
|
| |||||||||||||||||||
|
|
|
|
|
| ||||||||||||||||||||
|
|
|
|
|
| ||||||||||||||||||||
|
|
|
|
|
| 14 | 5/8" (36" hood) |
|
|
|
|
|
|
| 14 | 5/8" (36" hood) |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
| 17 | 5/8" (42" hood) | 17 | 5/8" (42" hood) |
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8" DIA. | * |
HOLE |
1 Determine whether hood will discharge vertically (3¼” 
x 10” or 7” Round), or horizontally (3¼” x 10” only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best
results, use a minimum number of transitions and elbows.
| 6 7/8" |
| 107/8" | |
| DUCT | 11" | 21/8" | |
45/8" | ACCESS |
| ||
HOLE |
|
| 25/8" | |
|
|
|
|
ELECTRICAL
ACCESS HOLE
(in cabinet bottom)
*Note the extra wood shim and mounting screw near the cabinet front, on the cabinet center line.
