Manuals / Brands / Household Appliance / Stove / Broan / Household Appliance / Stove

Broan RMIP33, RMIP45 13. CONNECT WIRING (ALL BLOWERS), 14. INSTALL THE ROUGH-IN PLATE (ALL BLOWERS), 15. INSTALL THE TRANSITION (INTERIOR BLOWER)

1 16

Download 16 pages, 4.53 Mb

- 9 -

13. CONNECT WIRING (ALL BLOWERS)

Connect cable into wiring box using provided wire connectors.

Connect wires as follow: BLACK to BLACK, WHITE to WHITE and

GREEN or BARE wire under ground screw. DO NOT FORGET TO

CONNECT THE GROUND. Reinstall wiring cover.

WARNING

Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with

all applicable codes and standards. Before connecting wires, switch power off at service panel and

lock service disconnecting means to prevent power from being switched on accidentally.

!

1

HD0007

1) Ground screw

INTERIOR BLOWER: Remove the cable knock-out on the top of the rough-in plate. Remove rough-in plate wiring

cover. Place the wire clamp in the knock-out hole, insert the cable through the wire clamp in the rough-in plate wiring

box. Tighten the wire clamp to secure the cable.

Position insert below the installed custom hood. Pull cable through hole in top of insert.

IN-LINE OR EXTERIOR BLOWER: Remove rough-in plate wiring cover and connect wiring (see instructions included

with in-line or exterior blower).

14. INSTALL THE ROUGH-IN PLATE (ALL BLOWERS)

INTERIOR BLOWER:Carefully install the rough-in plate

inside the top of the insert with four

(4) lock nuts. See picture beside.

IN-LINE OR EXTERIOR BLOWER: Refer to instructions included with rough-in kit. Secure the rough-in plate inside the

top of the insert with (4) lock nuts.

HD0042

15. INSTALL THE TRANSITION (INTERIOR BLOWER)

Slide the transition over the adapter/damper. Seal the transition to the

adapter/damper by using duct tape.

HD0091

Contents

Main MODELS RMIP33 AND RMIP45 READ AND SAVE THESE INSTRUCTIONS WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ! TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: CAUTION - RMIP33 AND RMIP45 INSERT SYSTEM - INTERIOR BLOWERS Flow deviator (supplied with Model 634 or 644 (roof cap) - RMIP33 AND RMIP45 INSERT SYSTEM - IN-LINE AND EXTERIOR BLOWERS Model 331H (600 cfm) or 332H (900 cfm) exterior blower Model 335 (1200 cfm) or 336 (1500 cfm) exterior blower Model 437 (High capacity roof cap) 1. SELECT BLOWER OPTION AND INSTALL DUCTWORK MODEL P5 (SINGLE) OR P8 (DOUBLE) INTERIOR BLOWER MODEL 331H, 332H, 335 OR 336 EXTERIOR BLOWER MODEL HLB3, HLB6, HLB9 OR HLB11 IN-LINE BLOWER 2. PREPARE THE INSTALLATION 3. INSTALL BACKSPLASH (OPTIONAL) 4. CUSTOM HOOD PREPARATION 1 1/2 When building a custom hood, always follow all applicable construction codes and standards. Standard 36 h. cooktop 8. CUT THE HOLE IN CUSTOM HOOD BASE RMIP33 321/2 RMIP45 441/2 6. INSTALL CUSTOM HOOD LINER (OPTIONAL) 7. INSTALL THE RMIPWC REMOTE CONTROL (OPTIONAL) 9. INSTALL BLOWER (INTERIOR OR EXTERIOR BLOWER) 11. INSTALL THE DEVIATOR (INTERIOR BLOWER) 12. INSTALL THE ADAPTER (INTERIOR BLOWER) 10. REMOVE THE KNOCK-OUT OPENING (INTERIOR BLOWER) 10 14 13. CONNECT WIRING (ALL BLOWERS) 1 14. INSTALL THE ROUGH-IN PLATE (ALL BLOWERS) 15. INSTALL THE TRANSITION (INTERIOR BLOWER) 16. DUCTING CONNECTION (ALL BLOWERS) Install the insert. Take care not to kink ducting when installing insert (step 17). Take care not to kink ducting or pinch electrical cable when installing insert. 17. INSTALL THE INSERT 18. INSTALL THE BLOWER (INTERIOR BLOWER) Single blower (P5) Dual blower (P8) Never plug the 2-prong blower cord to the 3-prong power supply cord. A B Baffle Filters 21. USE AND CARE 19. LIGHT BULBS 20. INSTALL FILTERS 22. OPERATION 12 3 21. USE AND CARE 123 RMIP33 WARRANTY SINGLE BLOWER/ROUGH-IN (Model P5) DUAL BLOWER/ROUGH-IN (Model P8)