Removing the presser foot holder | Brother CS6000I instruction

fSlowly lower the presser foot lever so that the presser foot pin snaps into the shank in the presser foot holder.

aPresser foot lever

XThe presser foot is attached.

gRaise the presser foot lever to check that the presser foot is securely attached.

Removing the presser foot holder

Remove the presser foot holder when cleaning the sewing machine or when installing a presser foot that does not use the presser foot holder, such as the quilting foot. Use the screwdriver to remove the presser foot holder.

■Removing the presser foot holder

aRemove the presser foot.

•For details, refer to “Replacing the presser foot” (page 24).

bUseholderthescrew.screwdriver to loosen the presser foot

aScrewdriver

bPresser foot holder

cPresser foot holder screw

■Attaching the presser foot holder

aAlign the presser foot holder with the lower- left side of the presser bar.

1

aPresser foot holder

bPresser bar

bHold the presser foot holder in place with your right hand, and then tighten the screw using the screwdriver in your left hand.

aScrewdriver

bPresser foot holder

cPresser foot holder screw

Note

●If the presser foot holder is not correctly installed, the thread tension will be incorrect.

25

Image 26

Brother CS6000I Removing the presser foot holder, Attaching the presser foot holder, Remove the presser foot

Contents

Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operation Contents Utility Stitches Names of Machine Parts and Their Functions Main parts Buttons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Accessories Optional accessories BSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch to Foot controller Changing the needle stop position Pass the thread around the pre-tension disk Threading the MachineWinding the bobbin ETurn on the sewing machine GTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the right Lower threading Actual size 11.5mm 7/16 inch This model Right side see arrow b until the cover clicks into place For models equipped with the quick-set bobbin Upper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown below Lightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Needle types and their uses Needle precautionsReplacing the Needle Fabrics Correct needle Checking the needleReplacing the needle Incorrect needle Installing the needle clamp Sewing with a twin needle Twin needle threading Mark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Attaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder Remove the presser foot General sewing procedure Sewing Turn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser foot BRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tight Changing the sewing direction Useful Sewing TipsTrial sewing Sewing curves Sewing stretch fabrics Using a free-arm styleSewing thin fabrics Slide the flat bed attachment to the left to release it Overcasting Stitches Attach overcasting foot G or zigzag foot J Select a stitch Basic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle position If the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn on Size of the buttonhole is set If the button does not fit in the button guide plate FPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics ESelect a stitch With stitch Select stitch Zipper Insertion Rev. Reverse Elastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching APPLIQUÉ, Patchwork and Quilt Stitching Appliqués Patchwork crazy quilt stitching Piecing Baste the fabric to be quilted Using the optional quilting guideQuilting DSelect stitch , or Free-motion quilting GAfter sewing is finished, slide the feed dog Bar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewing Once sewing is completed, Pullpossible.down the buttonhole lever as far as Decorative Stitching DTrim along the stitches FagotingScallop stitching Sew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathers Unfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Stitch Settings Utility stitches Rfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Thread ten LowerOr breaks Fabric is There is a high Stitches areSkipped Pitched noise While sewing Error Messages Operation beep for models equipped with the operation beep Index Numerics 30, 32 English 885-S33/S34/S36/S37 XC8835-4216