Winding the Bobbin
1 | 2 |
|
| Pass the thread through the hole | |
Pull up on the thread spool pin to lengthen the height. Place the thread spool on the pin | on the bobbin from inside. Use | ||
upper hole, not both. Place on | |||
and pass the thread around the bobbin winder | |||
bobbin shaft and slide to the right. | |||
|
| ||
3 | 4 | CAUTION | |
Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.
While holding the end of the thread, | When the bobbin starts to spin |
| 1 Wound evenly |
press the foot controller to begin | slowly and becomes full, release |
| |
winding the thread. Cut the thread | the foot controller. Cut the thread, | 1 | 2 Wound poorly |
from the top and proceed winding. | slide the bobbin winding shaft to | 2 | |
| the left and remove the bobbin. |
|
|
Inserting the Bobbin |
| ||
1 | 3 | 4 |
|
Threading the Needle
1
Raise the presser foot lifter.
2 | 3 | 4 |
Raise the thread | Place the thread spool on the | Pass the thread through the thread guide and down the | ||||||
its highest position by turning the | spool pin. | right channel on the front of the machine. | ||||||
handwheel. | (Don’t forget to pull up the pin) |
|
|
|
|
|
|
|
5 | 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pass the thread into the thread tension discs or behind the | Grasp the thread on both sides of the tension disc and pull to |
thread tension dial from the right to the left. | ensure it is in place. |
Raise the needle to its highest position and remove the bobbin case by pulling the latch.
2
Hold the bobbin case as shown. Insert the bobbin with the thread coming from the bottom toward the top and the thread tail hanging out of the bobbin case.
Pull the trailing thread through the slot, down and to the left, until it enters the delivery eye under the tension spring. CAUTION: Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.
Holding the bobbin case by the latch, align your finger with the top opening of the shuttle race, insert the case into the shuttle race and release the latch.
7 | 8 |
Guide the thread up the left channel, clear to the back of the opening around | Thread the needle from front to back and pull |
the | out about 2” of thread. |
|
Cleaning the Bobbin Case
1
Relative Chart of Sewing Fabrics, Needles and Thread Combinations
| Sewing Fabrics | Needle Sizes | Thread Sizes |
Very Thin | Fine tricot, Fine lace, Thin linen, | #65/9 | Cotton: 80 |
| Silk, Organza, Chiffon |
| Synthetic/Polyester Long Fiber |
|
|
| Fine Mercerized Cotton |
|
|
|
|
Lightweight | Voile, Taffeta, Synthetics, Silk, | #75/11 | Cotton: |
| Batiste |
| Silk: “A” |
|
|
| Synthetic/Polyester Long Fiber |
|
|
| Mercerized 50 |
23
Raise the needle to its highest position, | Slide the latch levers out from the |
pull the latch and remove the bobbin | retaining ring. |
case. |
|
Remove the power plug from the outlet.
4 
Remove the retaining ring.
Medium Weight | Cotton, Gingham, Poplin, | #90/14 | Cotton: |
| Percale, Pique, Satin, Velvet, | (Supplied with | Silk: “A” |
| Lightweight wool, Fine | your machine) | Synthetic/Polyester Long Fiber |
| corduroy, Suitings, Linen, |
| Mercerized |
| Muslin |
|
|
|
|
|
|
Heavyweight | Denim, Gabardine, Tweed, | #100/16 | Cotton: |
| Corduroy, Canvas, Duck |
| Mercerized Heavy Duty |
|
|
| Polyester Long Fiber |
|
|
|
|
Knits | Single knit, Double knit, Jersey, | #90/14 | Cotton Wrapped Polyester |
| Tricot | (Ball point) | Polyester Long Fiber |
|
| ||
Uses common replacement accessories: |
| ||
Bobbin: | Class 15 |
|
|
Needle: | Standard sewing machine needles |
| |
5 | 6 | 7 |
Remove the hook by grasping the center | Remove any accumulated lint and | Grasp the center post of the hook, match | ||||||||||||
post and pulling out. Note its position | thread with a brush. | the hook position opposite the driver and | ||||||||||||
related to the driver. |
|
|
|
|
|
|
|
| insert. | |||||
8 |
|
|
|
|
| 9 |
|
|
|
|
|
|
|
|
Insert the retaining ring with the notch | Push the latch levers into their locked |
up. | position. Replace the bobbin case. |
Light Bulb: | Small screw base sewing machine bulb |
Utiliza accesorios comunes de remplazo: | |
Carretel: | Clase 15 |
Agujas: | Agujas estándares para máquina de coser. |
Bombilla: | Para máquina de coser con base roscada pequeña |
Toll Free Phone
