Bryant 351DAS warranty Controls-Thermostatsand Zoning, Condensate Trap on LEFT Side, on RIGHT Side

INSTALLATION

This forced air furnace is equipped for use with natural or propane gas at altitudes 0 - 10,000 ft (0 - 3,050m). This furnace is for indoor installation in a manufactured (mobile) or modular home.

This furnace may be installed on combustible flooring in alcove or closet at minimum clearance from combustible material.

This appliance requires a special venting system. Refer to the installation instructions for parts list and method of installation. This furnace is for use with schedule-40 PVC, PVC-DWV, or ABS-DWV pipe, and must not be vented in common with other gas-fired appliances. Construction through which vent/air intake pipes may be installed is maximum 24 inches (600 mm), minimum 3/4 inches (19 mm) thickness (including roofing materials).

Furnace must be installed level, or pitched forward within 1/2 inch of level for proper drainage. Failure will result				LEVEL (0")
in equipment or property damage.				TO
				1/2" MAX
						FRONT
				DOWNFLOW
	MINIMUM INCHES CLEARANCE TO	This furnace is approved for
		DOWNFLOW installation. 1"
	COMBUSTIBLE CONSTRUCTION
				TOP/PLENUM
DOWNFLOW POSITION:
*	Mimimum front clearance for service 30 inches (762mm).		0"
				B A C K
† For installation on combustible floors only when installed on special base No. KGASB0201ALL,
	Coil Assembly, Part No. CD5 or CK5, or Coil Casing, Part No. KCAKC.					CE
						A
						N
					R
				U		T
				F
	MANUFACTURED MOBILE HOME STANDARDS					N
						O
						R
						F

	E
I	D
S

0"

This furnace must be installed in accordance with the manufacturer's instructions and Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 or, when such standard is not applicable, the ANSI A225.1, Standard for Manufactured Home Installation (Manufactured Home Sites, Communities and Set-Ups), or the Mobile Homes Standard CAN/CSA-Z240 MH Series-M86.

This furnace must be installed with a direct vent (combustion air and flue) system, and use a factory accessory termination kit.

SIDE

0"

Clearance in inches

			S E	R VI
					C E *
F R	O N
		T			30
					MIN

3"

BOTTOM

0"

†

Condensate Trap

on LEFT Side

COLLECTOR BOX

DRAIN TUBE

CONDENSATE TRAP

INDUCER HOUSING DRAIN TUBE

BURNER ENCLOSURE PRESSURE REFERENCE

TUBE ASSEMBLY

	TUBE ROUTING				Condensate Trap
					on RIGHT Side
		BURNER ENCLOSURE
		PRESSURE
		REFERENCE TUBE
		ASSEMBLY
					CAP / PLUG
		CAP / PLUG		LOWER COLLECTOR BOX
	LOWER COLLECTOR				PRESSURE TUBE
BOX PRESSURE TUBE
	UPPER COLLECTOR			UPPER COLLECTOR BOX
BOX PRESSURE TUBE
					PRESSURE TUBE
	GAS VALVE		GAS VALVE
		COLLECTOR BOX
		DRAIN TUBE		COLLECTOR BOX EXTENSION DRAIN
		INDUCER HOUSING			TUBE
					DRAIN TUBES ROUTED IN
		DRAIN TUBE
					FRONT OF GAS VALVE
		DRAIN TUBE			CONDENSATE TRAP
		COUPLING

NOTE: 1. All tubing must be connected securely and routed to avoid kinks and traps.	324997-201 REV. A / LIT
	A99001e

CONTROLS—THERMOSTATS AND ZONING
	For Use with 1-Speed Air Conditioner—TSTATBBNAC01-B
THERMOSTAT—NON-PROGRAMMABLE	For Use with 2-Speed Air Conditioner—TSTATBBN2S01-B
	For Use with 2-Speed Heat Pump—TSTATBBN2S01-B
	For Use with 1-Speed Air Conditioner—TSTATBBPAC01-B
THERMOSTAT—PROGRAMMABLE	For Use with 2-Speed Air Conditioner—TSTATBBP2S01-B
	For Use with 1-Speed Heat Pump—TSTATBBPDF01-B
	For Use with 2-Speed Heat Pump—TSTATBBP2S01-B or TSTATBBPDF01-B
THERMIDISTAT—PROGRAMMABLE THERMOSTAT	TSTATBBPRH01-B
with Humidity Control

—3—