BRYSTON 14B ST MANUAL
SPECIAL INSTRUCTIONS FEATURES AND SPECIFICATIONS:
Maximum continuous output power with both channels driven can only be realized on a 120 Volt 20 Amp or 230 Volt 10 Amp version of the 14B ST
Music is a “Dynamic and Transient” condi- tion and the power requirements fluctuate up and down over time with the audio sig- nal. Therefore, under most listening condi- tions the 15Amp/120 Volt version will be all that is required for the majority of domes- tic audio/video systems.
If more power is required, then a 14B - 20 Amp version is also available. You must have a minimum of 12 Gauge household electrical wire and a dedicated 20 Amp wall plug in order to utilize this feature. The other option available is to wire for a 240 Volt 10 Amp service and use the 230 Volt 10 Amp European model.
14B-120-Volt 15 Amp Version:
Power rating: | 500 Watts into 8 Ω |
| Distortion: | |
| Thd + N .005% 20Hz to 20kHz at 500 watts /8 ohms | |||
| 800 Watts into 4 Ω |
| ||
|
| IMD .005% 60 Hz + 7kHz mixed 4 to 1 | ||
Input impedance: |
|
| ||
|
| Noise – 115db 20Hz to 22kHz bandpass | ||
balanced | 15 k Ω |
| ||
|
| |||
unbalanced | 50 k Ω |
| Current consumption: | |
Sensitivity: |
|
| ||
|
| Both channels at full power with 8 ohm loads = 19.1A. | ||
bal input reg | 2 Volt in = 100 Watts / 8 | Ω | ||
Both channels at full power with 4 ohm loads = 30.7A. | ||||
bal input +6 | 1 Volt in = 100 Watts / 8 | Ω | ||
Both channels idle = 1.3 Amps | ||||
unbal | 1 volt in = 100 Watts / 8 | Ω | ||
|
14B-120-Volt 20 Amp Version:
Power rating: | 500 Watts into 8 Ω |
| Distortion: | |
| Thd + N .005% 20Hz to 20kHz at 500 watts /8 ohms | |||
| 800 Watts into 4 Ω |
| ||
|
| IMD .005% 60 Hz + 7kHz mixed 4 to 1 | ||
Input impedance: |
|
| ||
|
| Noise – 115db 20Hz to 22kHz bandpass | ||
balanced | 15 k Ω |
| ||
|
| |||
unbalanced | 50 k Ω |
| Current consumption: | |
Sensitivity: |
|
| ||
|
| Both channels at full power with 8 ohm loads = 19.1A. | ||
bal input reg | 2 Volt in = 100 Watts / 8 | Ω | ||
Both channels at full power with 4 ohm loads = 30.7A. | ||||
bal input +6 | 1 Volt in = 100 Watts / 8 | Ω | ||
Both channels idle = 1.3 Amps | ||||
unbal | 1 volt in = 100 Watts / 8 | Ω | ||
|
14B-230-Volt 10 Amp Version
Power rating: | 500 Watts into 8 Ω |
| Distortion: | |
| Thd + N .005% 20Hz to 20kHz at 500 watts /8 ohms | |||
| 800 Watts into 4 Ω |
| ||
|
| IMD .005% 60 Hz + 7kHz mixed 4 to 1 | ||
Input impedance: |
|
| ||
|
| Noise – 115db 20Hz to 22kHz bandpass | ||
balanced | 15 k Ω |
| ||
|
| |||
unbalanced | 50 k Ω |
| Current consumption: | |
Sensitivity: |
|
| ||
|
| Both channels at full power with 8 ohm loads = 9.5A. | ||
bal input reg | 2 Volt in = 100 Watts / 8 | Ω | ||
Both channels at full power with 4 ohm loads = 15.3A. | ||||
bal input +6 | 1 Volt in = 100 Watts / 8 | Ω | ||
Both channels idle = 1.3 Amps. | ||||
unbal | 1 volt in = 100 Watts / 8 | Ω | ||
|
Note: Continuous 2 channel power is limited by specific circuit breaker limitations.
Page 5