ELECTRICAL REQUIREMENTS

CAUTION - Do not plug-in the brewer until specified in Initial

Set-Up.

The A10/A10 Automatic Brewer has an attached cordset and requires 2-wire grounded service rated 120 volts ac, 10 amp, single phase, 60 Hz.

The A10A/A10A Automatic Brewer has an IEC 320 connector and matching cordset and requires 2-wire grounded service rated 230 volts ac, 10 amp, single phase, 50-60 Hz. The appropriate cordset connector must be supplied when installing the brewer.

120 VOLT

230 VOLT CE

CE REQUIREMENTS

•This appliance must be installed in locations where it can be overseen by trained personnel.

•For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.

•Appliance shall not be tilted more than 10° for safe operation.

•An electrician must provide electrical service as specified in conformance with all local and national codes.

•This appliance must not be cleaned by water jet.

•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of this appliance by a person responsible for its safety.

•Children should be supervised to ensure they do not play with the appliance.

• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.

• Machine must not be immersed for cleaning.

PLUMBING REQUIREMENTS - A10 AUTOMATIC ONLY

This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi from a 1/2” or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi to reduce it to 50 psi. The water inlet fitting is 1/4” flare.

NOTE – Bunn-O-Matic recommends 1/4” copper tubing for installations of less than 25 feet and 3/8” for more than 25 feet from the 1/2” water supply line. At least 18 inches of an FDA approved flexible beverage tubing, such as reinforced braided polyethylene or silicone, before the brewer will facilitate movement to clean the countertop. It can be purchased direct from Bunn-O-Matic (part number 00326-0000).

As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.

Plumbing Hook-Up

1. Attach the flare fitting from the short piece of tubing on the flow control (supplied) to the water inlet fitting on the left rear side of the brewer.

2. Flush the water line and securely attach it to the flare fitting on the strainer.

3. Turn on the water supply.

CONTINUED

 

 

43422.1 010311

 

7

 

 

Page 6 Page 8
Page 7
Image 7
Bunn A10 specifications Electrical Requirements, Set-Up
Page 6 Page 8

A10 specifications

The Bunn A10 is a high-performance coffee brewer designed to meet the demands of commercial establishments. Renowned for its reliability, efficiency, and quality brewing, it is a popular choice among coffee shops, restaurants, and other venues that serve high volumes of coffee.

One of the standout features of the Bunn A10 is its large capacity. With the ability to brew up to 10 gallons of coffee per hour, it is well-suited for busy environments where speed and volume are essential. The machine also includes a large 3.8-liter stainless steel water tank, ensuring that hot water is always ready for brewing, which greatly reduces wait times and enhances service efficiency.

The Bunn A10 employs an advanced spray head technology for optimal coffee extraction. The specially designed showerhead delivers water evenly over the coffee grounds, promoting uniform saturation and ensuring that the full flavor profile of the coffee is achieved. This technology helps coffee shops maintain consistent quality, a key factor for customer satisfaction.

In terms of user-friendliness, the Bunn A10 features an intuitive control panel, making it easy for staff to operate. The machine is designed for simplicity, with straightforward programming options that allow users to adjust brew times and temperatures to create the perfect cup of coffee. Additionally, the unit is constructed for durability with stainless steel components that can withstand the rigors of daily use.

Another key characteristic of the Bunn A10 is its energy-efficient design. The machine is equipped with a hot water tank that is constantly maintained at an optimal temperature, minimizing energy waste while ensuring that it is always ready to brew. This is particularly beneficial for high-demand settings, as it reduces downtime and ensures a steady supply of freshly brewed coffee.

Maintenance is also a significant consideration in the Bunn A10's design. The machine features a self-diagnostic system that helps predict maintenance needs before they become an issue. This proactive approach not only maximizes uptime but also extends the machine's lifespan.

In summary, the Bunn A10 coffee brewer is a robust and efficient choice for any commercial setting. Its ability to produce large quantities of high-quality coffee quickly, combined with user-friendly features and advanced brewing technology, makes it a top choice for businesses focused on delivering exceptional coffee experiences.
Top Page Image Contents