Bunn LCA-2 LCC-2 WARNING

3

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual. They were written for your protec-

tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels.

00656.0000

00986.0002

11646.0002

! WARNING

DO NOT OVERLOAD CIRCUIT.

ALWAYS ELECTRICALLY GROUND THE CHASSIS

OR ADAPTOR PLUG.

DO NOT DEFORM PLUG OR CORD.

FOLLOW NATIONAL AND LOCAL ELECTRICAL CODES.

KEEP COMBUSTIBLES AWAY.

FAILURE TO COMPLY RISKS EQUIPMENT

DAMAGE, FIRE OR SHOCK HAZARD.

READ THE ENTIRE OPERATING MANUAL

BEFORE USING THIS PRODUCT

00986.0002E 5/98 ©1994 Bunn-O-Matic Corporation

10044.0000

INTRODUCTION

The Liquid Coffee Ambient Dispenser (LCA-2) and the Liquid Coffee Chilled Dispenser (LCC-2) delivers two

types of coffee plus hot water. The dispenser can be set up for continuous draw (by the cup) for self-serve

applications, or portion-control to fill carafes and decanters for wait staff. Product Flavor Profile is extended with

chilled product storage cabinet featured in the LCC-2.

12652.0000

WARNINGHAZARDOUSVOLTAGE

UNPLUG BREWER

BEFORE REMOVING!

Optional Field Wiring

208-240 V, 25.8 A, 6200 W1PH, 2-Wire, 60HZor120/208-240 V, 25.8 A, 6200 W1PH, 3-Wire, 60HZ

28181.0003

! WARNING HOT LIQUIDS

! AVERTISSEMENT LIQUIDES CHAUDS

34766 112502

Contents

Main BUNN INSTALLATION & OPERATING MANUAL BUNN-O-MATIC CORPORATION LCA-2 LCC-2 ! WARNING HOT LIQUIDS BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY CONTENTS USER NOTICES ! WARNING INTRODUCTION WARNING HAZARDOUS VOLTAGE Optional Field Wiring 208-240 V, 25.8 A, 6200 W 1PH, 2-Wire, 60HZ or 120/208-240 V, 25.8 A, 6200 W 1PH, 3-Wire, 60HZ ! WARNING HOT LIQUIDS ELECTRICAL REQUIREMENTS FIELD WIRING TERMINAL BLOCK DIAGRAM PLUMBING REQUIREMENTS INITIAL SET-UP ELECTRICAL HOOK-UP PLUMBING HOOK-UP SETTING DISPENSER FLOW RATE Field Calibration of the Concentrate Pumps / Dispenser Flow Rates. SELECTING THE CORRECT PUMP TUBING Setting Dispenser Flow Rate Priming the Concentrate Lines Tubing Installation Instructions Tube Selection Chart. OPERATING CONTROLS AND INTERFACE (Located behind the splash guard panel) INITIAL FILL & HEAT FlavorGard Feature Programming the Dispenser Rinse Alarm Feature Brew Temperature Lockout Feature PROGRAMMING THE DISPENSER Tube Selection Chart Flavor Guard Tube Selection Chart Page Field Calibration Rinse Alarm Pump Calibration Chilled Unit LOADING THE CONCENTRATE Tube Installation Decal Rinsing PRIMING THE CONCENTRATE LINES OPERATING THE DISPENSER Programming Functions CLEANING & PREVENTATIVE MAINTENANCE Programming Functions REPLACING THE PUMP TUBING Tube Replacement Instruction Weekly Sanitizing instructions DRAINING THE HOT WATER TANK Initial Fill & Heat Troubleshooting Front Panel LED Display Messages Optional Field Wiring Rinse Procedure Fault Messages. Dispenser Diagnostics Troubleshooting (Continued) Field Calibration of the Concentrate Pumps / Dispenser Flow Rates Priming the Concentrate Lines Tube Replacement Instructions Field Calibrating the Empty BIB Warning Operating Controls and Interface Programming the Dispenser Field Calibration of the Concentrate Pumps / Dispenser Flow Rates (Continued) 34641.0000C 12/02 2002 BUNN-O-MATIC CORPORATION SCHEMATIC WIRING DIAGRAM LCA-2, LCA-2C,LCC-2,LCC-2C LLC Models only SW. & THERMOSTAT 34641.0001B 12/02 2002 BUNN-O-MATIC CORPORATION C SCHEMATIC WIRING DIAGRAM LCC-2A/LCA-2A LLC Models only 34766 121602 230 VOLTS AC 2 WIRE SINGLE PHASE 50 HZ SW. & THERMOSTAT