Manuals / Bush Hog / Lawn and Garden / Lawn Mower

Bush Hog RMB 1660 manual Safety

Models: RMB 1660

1 108

Download 108 pages 27 Kb

Page 27

Image 27

SAFETY

Driveline Hazards

P/N D388

Decal D388 consists of the following multi-hazards.

RMB 1660 11/10

Safety Section 1-21

SAFETY

Page 27

Image 27

Contents

REAR-MOUNT BOOM MOWER OPERATOR’S MANUALBUSH HOG To the Owner/Operator/Dealer OSHA TRAINING REQUIREMENTS Alamo Group Ag. Division is willing to provide one 1 AEM Mower Safety Practices VideoINTRODUCTION SECTION TABLE OF CONTENTSSAFETY SECTION ASSEMBLY SECTIONMAINTENANCE SECTION Safety Section SAFETY SECTIONSAFETY SAFETYGeneral Safety Instructions and Practices SG-4 SAFETYSAFETY Operator Safety Instructions and PracticesSAFETY SAFETYSG-36 “Wait a minute...Save a life!” SAFETYSAFETY Connecting & Disconnecting Implement Safety Instructions & PracticesSBM-7 SAFETYSAFETY Equipment Operation Safety Instructions and PracticesSAFETY SAFETYSAFETY SAFETYNOTE Where there are grass and weeds high enough to hide debris that could be SAFETY SAFETYSAFETY SAFETYSGM-06 SAFETY SAFETYSGM-08 SAFETY SAFETYMaintenance and Service Safety Instructions and Practices SAFETY SAFETYSEE YOUR BUSH HOG DEALER SAFETYSAFETY Transporting Safety Instructions and PracticesSAFETY SAFETYSAFETY SAFETYConcluding Safety Instructions and Practices SAFETY SAFETYDecal Location DESCRIPTION SAFETYSAFETY LEVELDESCRIPTION SAFETYSAFETY LEVELSAFETY SAFETYDecal Description SAFETY SAFETYSAFETY SAFETYSAFETY SAFETYSAFETY SAFETYSAFETY SAFETYSAFETY SAFETYEmployer-Employee Operator Regulations SAFETYSAFETY Federal Laws and RegulationsPage Introduction Section INTRODUCTION SECTIONINTRODUCTION INTRODUCTIONINTRODUCTION INTRODUCTIONINTRODUCTION INTRODUCTIONATTENTION OWNER/ OPERATOR Assembly Section ASSEMBLY SECTIONTRACTOR SELECTION ASSEMBLYASSEMBLY MINIMUM TRACTOR WEIGHTS - including ballast weight if necessaryFitting Operator Guard ASSEMBLYASSEMBLY TRACTOR PREPARATIONSuggestions to increase stability ASSEMBLYASSEMBLY DEALER SETUP INSTRUCTIONSASSEMBLY ASSEMBLYATTACHMENT TO TRACTOR ASSEMBLY ASSEMBLYNOTE As lift occurs be aware the machine may tilt slightly ASSEMBLY ASSEMBLYNOTE The quadrant pin must be fitted in the lowest hole on the stabilizer in order that it acts as a “Bottom Stop”. This will prevent the machine from dropping when stopped and permit the tractor’s in-built transport protection system to function correctly during operation and transportation ASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYFlail Head Attachment FITTING CONTROL UNIT IN CAB ASSEMBLYASSEMBLY OIL REQUIREMENTSREMOVAL FROM TRACTOR ASSEMBLYASSEMBLY RUNNING UP PROCEDURESUBSEQUENT ATTACHMENT TO IDENTICAL TRACTOR ASSEMBLYASSEMBLY STORAGEPage Operation Section OPERATION SECTIONRMB 1660 11/10 OPERATIONPower Arm Attachments OPERATION1. Standard Equipment and Specifications Machine SpecificationsPERSONAL PROTECTIVE EQUIPMENT PPE OPERATIONOPERATION 2. OPERATOR REQUIREMENTS3.1 ROPS and Seat Belt OPERATIONOPERATION 3. TRACTOR REQUIREMENTS3.4 Tractor Ballast OPERATIONOPERATION 3.3 Tractor Lighting and SMV EmblemOPERATION 3.5 Tractor Safety Devices3.6 Tractor Horsepower CAT II Implement/ Hitch SpecificationOPERATION 3.9 Front End Weight3.10 Power Take Off PTO OPERATION4.2 Dismounting the Tractor OPERATIONOPERATION 4.1 Boarding the TractorOPERATION OPERATION5. STARTING THE TRACTOR OPERATION 6. PRE-OPERATION INSPECTION AND SERVICE6.1 Tractor Pre-Operation Inspection/Service OPERATION6.2 Boom Unit Pre-Operation Inspection and Service OPERATIONOPERATION OPERATION OPERATIONOPS-B- 0023J OPERATION OPERATIONOPERATION OPERATIONOPERATION OPERATIONDO NOT OPERATE an UNSAFE TRACTOR or MOWER OPERATIONOPERATION Boom Mower PRE-OPERATION InspectionDO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT OPERATIONOPERATION Tractor PRE-OPERATION Inspection7.1 Cable Controls - Identification & Function OPERATIONOPERATION 7. MACHINE CONTROLSOPERATION OPERATION7.2 Lever Functions OPERATION OPERATION7.3 Rotor Control 8. BREAKAWAY Powered SlewOPERATION OPERATION10. FORWARD SPEED OPERATIONOPERATION 9. ROTOR OPERATING SPEED12. Hedge Cutting Procedure OPERATIONOPERATION 12.1 Working on Adverse Slopes OPERATIONOPERATION 13. Lift Float Kit OptionalOPERATION OPERATION14. DRIVING THE TRACTOR AND IMPLEMENT 14.1 Starting the Tractor 14.2 Brake and Differential Lock SettingOPERATION OPERATION14.3 Driving the Tractor and Boom OPERATIONOPERATION 15. OPERATING THE TRACTOR AND IMPLEMENT15.1 Foreign Debris Hazards 15.2 Bystanders/Passersby PrecautionsOPERATION OPERATION15.3 Engaging the Power Take Off PTO OPERATIONOPERATION 15.5 Operating the Mower OPERATIONOPERATION 15.4 Operating Speed and Ground SpeedOPERATION OPERATIONGrass Flail OPERATIONOPERATION 15.6 Operating the Attached Mower HeadsOPERATION OPERATION15.7 Shutting Down the Attached Head 17. TRANSPORTING THE TRACTOR AND IMPLEMENT OPERATIONOPERATION 16. TRACTOR, BOOM, AND ATTACHED HEAD STORAGEOPERATION OPERATION17.1 Transport Position 19. TRANSPORT POSITION-Head Removal OPERATIONOPERATION 18. TRANSPORT POSITION-Head Attached19.2 Transporting on Public Roadways OPERATIONOPERATION 19.1 Transport HeightOPERATION OPERATIONOPERATION OPERATIONOPERATION OPERATION19.3 Hauling the Tractor and Implement TROUBLE 20. TROUBLESHOOTING GUIDEOPERATION OPERATIONPOSSIBLE CAUSE OPERATIONOPERATION TROUBLEPage Maintenance Section MAINTENANCE SECTIONGeneral MAINTENANCEMAINTENANCE LUBRICATIONHYDRAULIC SYSTEM MAINTENANCEMAINTENANCE Filtration MaintenanceHose Warranty MAINTENANCEMAINTENANCE Hose ReplacementCABLES MAINTENANCEMAINTENANCE FLAILHEADSTORAGE MAINTENANCEMAINTENANCE PTO GEARBOXMAINTENANCE MAINTENANCEPROPER TORQUE VALUES FOR FASTENERS LIMITED WARRANTY THIS LIMITED WARRANTY SHALL NOT APPLYDISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES TO THE OWNER/OPERATOR/DEALER Printed U.S.A RMB 1660 REAR MOUNT BOOM MOWERRMB 1660-11/10 P/N 50068816C