Cabela's 51-7403 Cleaning Instructions, Grounding Instructions, Sharp Blade, Extension Cords

CLEANING INSTRUCTIONS

WARNING! Before cleaning, assembling or disassembling the Food Slicer, make sure the Food Slicer Motor is OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

WARNING! Before cleaning, assembling or disassembling the Food Slicer, make sure the Food Slicer Motor is OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

HANDLE CAREFULLY!

KEEP FINGERS AWAY FROM THE BLADE!

NEVER FEED FOOD BY HAND.

ALWAYS USE THE FOOD PUSHER!

WARNING!

SHARP BLADE

HANDLE CAREFULLY!

KEEP FINGERS AWAY FROM THE BLADE!

NEVER FEED FOOD BY HAND.

ALWAYS USE THE FOOD PUSHER!

Always use completely assembled Food Slicer

with Food Carriage and Food Pusher.

Protective/cut-resistant Kevlar gloves are recommended

WARNING!

SHARP BLADE

Always use completely assembled Food Slicer

with Food Carriage and Food Pusher.

Protective/cut-resistant Kevlar gloves are recommended

whenever handling the Blade!

whenever handling the Blade!

GROUNDING INSTRUCTIONS

1.	ALWAYS disconnect the appliance from the power source before cleaning.
2.	Never immerse the Motor Assembly of this appliance in water or other liquid.
3.	The Blade, Food Presser, and Food Tray can all be hand washed in hot soapy
water. Because these parts come in contact with food, they should be sanitized by
being dipped in a solution of 2 ounces (0.06 L) of unscented non-chlorine bleach
mixed with 5 gallons (19 L) of water. Allow sanitized parts to air dry. Do not use
harsh abrasives to clean any part of the Food Slicer. Use extreme caution when
handling or cleaning the Blade, as it is extremely sharp! Do not leave Blade
underwater; trying to handle sharp objects in water can be hazardous. It is
highly recommended to wear cut-resistant Kevlar Gloves when removing,
cleaning and re-installing the Blade.
4.	Set the Thickness Adjustment Knob to “0”.

GROUNDING

This appliance must be grounded while in use to protect the operator from electrical shock. The appliance is equipped with a 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding-type receptacle. The appliance has a plug that looks like Figure A. An adaptor, Figure B, should be used for connecting Figure A plugs to two-prong receptacles. The grounding tab which extends from the adaptor must be connected to a permanent ground such as a properly grounded outlet box as shown in Figure C using a metal screw.

Circuit

GroundingFigure A

Conductor

Grounding

Prong

5. Remove Food Presser and rotate the Sliding Food Carriage out of the way in

order to allow for easy access to the Blade.

Figure B

EXTENSION CORDS

6.To remove the Blade hold the Blade with one hand and use a coin to unlock the Blade Locking Screw by turning it clockwise Figure 6. Carefully pull the Blade off and hold it by using the hole in the center of the Blade.

7.Clean the outer surface of the Food Slicer Body & Base with a damp cloth. Mild detergent or water can be used to dampen the cloth. Wipe away from the Blade, NEVER wipe toward the Blade. Never immerse Motor Assembly in water or any other liquid. Do not use steel wool, abrasive cleaners, or sharp utensils to clean.

Figure 6

Rotate clockwise to remove.

Use only 3-wire extension cords which have 3-prong grounding-type plugs and a 3-pole cord connector that accepts the plug from the appliance. Use only extension cords having an electrical rating not less than the rating of the appliance. DO NOT use damaged extension cords. Examine extension cord before using and replace if damaged. DO NOT abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges.

Metal

Grounding

Screw

Cover of

Grounded

Outlet Box

Figure C

Grounding

Means

AA2220

8.To allow for easier cleaning, the Thickness Adjustment Knob can be turned past “0” to allow the Gauge Plate to slide back. NOTE: Use this feature only with Blade removed. (After cleaning and before reassembly, reset the Thickness Adjustment Knob to “0”.)

9.After cleaning and drying, install the Blade and Blade Screw to the Motor Assembly in reverse order of step 6. Make sure the Blade Locking Screw is properly engaged and tightened. Rotate the Sliding Food Carriage back to its proper position and re- install the Food Presser.

-8-

-5-