Cabletron Systems 6H203-24, 6H253-13 A

Specifications A-1

Specifications

This appendix provides operating specifications for the Cabletron Systems SmartSwitch Interface

Modules. Cabletron Systems reserves the right to change these specifications at any time without

notice.

A.1 MODULE SPECIFICATIONS

A.2 PHYSICAL PROPERTIES

A.3 ENVIRONMENTAL REQUIREMENTS

Processors: Intel i960 RISC processor control Power PC

Dynamic Random Access

Memory (DRAM): 20 MB (expandable to 32 MB)

FLASH Memory: 8 MB

Shared Memory: 4 MB

Dimensions: 46.43 H x 6.05 W x 29.51 D (cm)

18.28 H x 2.38 W x 11.62 D (in)

Weight (Unit): 2.72 kg (6 lb)

MTBF (Predicted): 200,000 hours

Operating Temperature: 5°C to 40°C (41°F to 104°F)

Storage Temperature: -30°C to 73°C (-22°F to 164°F)

Operating Relative Humidity: 5% to 90% (non-condensing)

Contents

Main Page i Only qualified personnel should perform installation procedures. NOTICE ii FCC NOTICE INDUSTRY CANADA NOTICE VCCI NOTICE iii CABLETRON SYSTEMS, INC. iv v CABLETRON SYSTEMS SALES AND SERVICE, INC. vi vii CABLETRON SYSTEMS LIMITED viii ix DECLARATION OF CONFORMITY Page xi Contents 1 xii 2 3 INDEX 4 A Figures xiv Tables About This Guide USING THIS GUIDE Important Notice STRUCTURE OF THIS GUIDE RELATED MANUALS DOCUMENT CONVENTIONS The following conventions are used throughout this document: Introduction 1.1 OVERVIEW Important Notice Page Page 1.1.4 Full Duplex Switched Ethernet 1.1.5 SmartTrunk 1.1.6 Remote Monitoring (RMON) 1.1.7 Broadcast Suppression 1.1.8 Port/VLAN Redirect Functions 1.1.9 Rate Limiting 1.1.10 GARP Switch Operation 1.1.11 Flow Control 1.1.12 802.1 Port Priority 1.1.13 Management 1.1.14 Switching Options 1.1.15 Distributed Chassis Management 1.1.16 Optional HSIMs and VHSIMs 1.1.17 Standards Compatibility 1.1.18 LANVIEW Diagnostic LEDs 1.1.19 Year 2000 Compliance 1.2 GETTING HELP Page Network Requirements 2.1 SmartTrunk 2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK Installation 3.1 UNPACKING THE MODULE 3.2 INSTALLING OPTIONS 3.3 INSTALLING THE MODULE INTO THE 6C105 CHASSIS Page 3.4 CONNECTING TO THE NETWORK 3.4.1 Connecting Twisted Pair Cables to Fixed Ports Page 3.5 COMPLETING THE INSTALLATION Troubleshooting 4.1 USING LANVIEW 4.1.1 The LED Mode Switch Page Using LANVIEW Speed Status 3380_4.1 Figure 4-1 LANVIEW LEDs Troubleshooting 4-3 Page Page 4.2 TROUBLESHOOTING CHECKLIST Page Page Page Page 4.3 USING THE RESET BUTTON 6H203-24 Page A Specifications A.3 ENVIRONMENTAL REQUIREMENTS A.1 MODULE SPECIFICATIONS A.2 PHYSICAL PROPERTIES A.4 INPUT/OUTPUT PORTS A.5 COM PORT PINOUT ASSIGNMENTS A.6 REGULATORY COMPLIANCE Page B Switch Settings, Upgrades, and Installations B.1 SETTING THE MODE SWITCHES Page B.2 SIMM UPGRADE B.2.1 Locating SIMMs B.2.2 Installing the DRAM SIMM B.3 INSTALLING OPTIONAL HIGH SPEED INTERFACE MODULES Page Index