The Com-Pak™ Plus
OWNER’S GUIDE
| The |
| ||||
Side | Grill Front | Wall Can Side |
|
| ||
| 12” | 111/2” |
| 10” | Wall Can Bottom | |
| 29.21 |
| ||||
| 30.48 |
| 25.4 | 13/4” | 11/4” | |
|
|
|
| |||
|
| 31/4” |
|
| 4.45 | 3.18 |
|
| 11/4” |
|
|
| |
|
| 8.26 |
|
| 4” | |
|
|
| 3.18 | 3” | ||
|
|
|
|
| 10.16 | |
|
|
|
|
| 7.62 | |
|
|
|
|
|
| |
| 9” |
|
|
| 77/8” |
|
| 22.86 |
|
|
| 20.00 |
|
| The |
| ||||
Side | Grill Front |
|
| Wall Can Side | ||
|
|
| 12” | 111/8” | 10” | |
|
|
| 30.48 | 28.26 | 25.4 | |
| 161/4” |
|
|
|
|
|
| 41.27 |
|
|
|
|
|
| 3” |
| 4” | Wall Can |
| |
| 7.62 |
| 10.16 | Bottom |
| |
| 141/2” |
|
|
|
|
|
| 36.83 |
|
|
|
|
|
TOOLS REQUIRED: | Utility Knife | |
Phillips Screwdriver | 4 | 11/2“ Wood Screws |
Straight Screwdriver | 3 | Insulated Wire Connectors |
Wire Strippers | 1 | Strain Relief Connector |
|
|
|
Features & Benefits
•Primary and secondary thermal safeguards
•Commercial grade high temperature manual reset
•Over temperature one-time thermal device
•Nichrome element wrapped around mica insulators for durability
•Powder coat paint process eliminates sharp cutting edges
•Two year extended warranty
•Wall can designed for ease of installation
•Factory tested
MODELS
The |
|
| |
C051 | *C051T | C152 | *C152T |
C052 | *C052T | C202 | *C202T |
C072 | *C072T | C208 | *C208T |
C102 | *C102T | C101 | *C101T |
C122 | *C122T | C151 | *C151T |
The |
|
| |
CT252 | *CT252T | CT102 |
|
CT302 | *CT302T |
|
|
CT402 | *CT402T |
|
|
CT408 | *CT408T |
|
|
*Standard
IMPORTANT INSTRUCTIONS
WARNING
Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on power while you are working on the heater. Failure to do so could result in serious electrical shock, burns, or possible death.
1.Read all instructions before using this heater.
2.Read all information labels. Verify that the electrical supply wires are the same voltage as the heater.
3.All electrical work and materials must comply with the National Electric Code (NEC), the Occupational Safety and Health Act (OSHA), and all state and local codes.
4.Connect the grounding pigtail (copper wire) provided in the wall can to the supply ground wire.
5.If you need to install a new circuit or need additional wiring information, consult a qualified electrician.
6.Protect electrical supply from kinks, sharp objects, oil, grease, hot surfaces or chemicals.
7. WARNING
Overheating or fire may occur. Do not install the heater in a floor, behind doors, or outdoors.
8. WARNING
Fire or explosion may occur. Heater has hot and arcing or sparking parts inside. Do not install heater in any area where combustible vapors, gases, liquids, or excessive lint or dust are present.
9. WARNING
Burn Hazard. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use extreme caution when any heater is used by or near children or invalids and whenever the heater is left operating unattended.
10. WARNING
Risk of Electrical Shock. Keep all foreign objects out of heater. Do not operate after heater malfunctions or has been dropped or damaged in any manner.
11. WARNING
Risk of Fire. Do not block heater. Heater must be kept clear of all obstructions: a minimum of 3 feet in front, 6 inches above and on both sides. Heaters must be kept clean of excessive lint, dirt and debris. (See Maintenance Instructions).
12.Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.