Grounding Instructions

This heater is for use on 240 (or 208) volts. The cord has a plug as shown to the right. No adapter is available for this blade configu- ration, and none should be used. The outlet type is a 240 (or 208) volt grounding outlet. When properly installed, it provides a ground connection through the cord to the heater to protect the operator from electrical shock.

CGH562 – 30 AMP

Plug

Configuration

Receptacle Configuration

Installation Instructions

CAUTION: Heater will operate on either 240 or 208 volts. Check heater voltage and phase on label on back of heater to make sure they are the same as the electrical service supplied. See plug configuration. Altering the cord in any way will void the warranty! Be sure that the electrical receptacle is of the configuration and capacity appropriate for the heater.

Floor Application

This heater may be used for floor or flat surface mounting. After placing the heater on floor or other flat surface in an appropriate location, insert plug into the proper type wall outlet.

Wall or Ceiling Mount Application

Heater can be mounted on wall or ceiling with proper anchoring provisions. The wall/ceiling mounting structure and anchoring provisions must be of sufficient strength to support the combined weight of the heater and mounting bracket.

Specifications

MODEL

WATTS

VOLTS (60 Hz)

BTUs

AMPS

PLUG TYPE

CGH562

5600 / 4200

240 / 208

19,107 / 14,322

23.4 / 20.2

30 Amp

Operation and Maintenance

How To Operate Your Heater

1.Turn the thermostat knob fully clockwise .

2.When the room reaches your comfort level, turn the thermostat knob counter clockwise until the heater shuts off. One or two minor adjustments may be necessary as the heat becomes better distributed throughout the area.

3.To reduce the room temperature, turn the knob counter clockwise. To increase the room temperature, turn the knob clockwise .

Continuous Fan Operation

In order to activate the continuous fan feature, set rocker switch to the “ON” position. The elements will continue to cycle according to the thermostat setting. For no heat, turn the thermostat knob to full counterclockwise position . With fan in “AUTO” position, fan will cycle with the thermostat.

Maintenance, Cleaning, & Storage

The motor is permanently lubricated. This heater does not require routine maintenance other than the occasional cleaning of the intake grill opening to prevent clogging.

WARNING WHEN CLEANING HEATER, BE SURE TO DISCONNECT HEATER CIRCUIT.

To disconnect heater, turn thermostat control knob to full

counterclockwise position, then remove plug from electrical outlet before cleaning or performing any maintenance. Allow heater to cool. IMPORTANT: Heater must be unplugged before performing any maintenance.

To clean air intake grill use vacuum with brush attachment or high pressure air. If the heater malfunctions or has been damaged, or

if the cord or plug has been damaged, repairs must be made by a qualified electrician or authorized service facility. Do not operate until repairs have been made.

For dusting, use a soft cloth. For cleaning, use only a damp rag and nonabrasive dish detergent. Do not use abrasive or chemical cleaners as these may damage the finish. If heater is used in a dusty location, use a vacuum cleaner dust brush to remove dust and other foreign particles from the grill. Always unplug cord and wind it around heater handles when not using. Keep heater in a safe location for storage.

Any other servicing should be performed by an authorized service representative.

When the heater is not in use, unplug and store in a clean, dry environment. The handle may also be used to wrap the power cord around for safe storage.

Temperature Limiting Device

All heaters are equipped with thermally actuated auto reset limit protection which automatically disconnects heating element and motor in the event normal operating temperatures are exceeded. If heater should fail to operate with thermostat turned clockwise to its limit, disconnect heater and wait a few minutes allowing heater to cool. Operation of the safety thermal limit control invariably indicates that the heater has been subjected to abnormal conditions, such as a partial or complete blockage of the air intake or exit. Be sure to keep these areas clear in order to allow proper air circulation. It is recommended that the heater be checked by a qualified electrician or repair service to insure the heater has not sustained any damage.

Warranty

Maintenance: For more effective and safer operation and to prolong the life of the heater, read the Owner’s Guide and follow the maintenance instructions included with each heater. Failure to properly maintain the heater will void any warranty and may cause the heater to function improperly. Warranties are non transferable and apply to original consumer only. Warranty terms are set out below.

LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any Cadet Garage/Utility Unit Heater (CGH) element or motor found to be defective within one year after the date of purchase.

THESE WARRANTIES DO NOT APPLY:

1.Damage occurs to the product through improper installation or incorrect supply voltage;

2.Damage occurs to the product through improper maintenance, misuse, abuse, accident, or alteration;

3.The product is serviced by anyone other than Cadet;

4.If the date of manufacture of the product cannot be determined;

5.If the product is damaged during shipping through no fault of Cadet.

6.CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRITTEN

WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.

7.IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WARRANTIES.

8.These warranties give you specific legal rights, and you may also have other rights which vary from state to state. Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with its products other than as set out herein.

If you believe your Cadet product is defective, please, contact Cadet Manufacturing Co. at 360-693-2505, during the warranty period, for instructions on how to have the repair or replacement processed. Warranty claims made after the warranty period has expired will be denied. Products returned without authorization will be refused.

Parts and Service

Visit http://support.cadetco.com for information on where to obtain parts and service.

©2010 Cadet Manufacturing Co.

Printed in U.S.A. Rev. 12/10 #720102

Page 2
Image 2
Cadet CGH562 Grounding Instructions, Installation Instructions, Specifications, Operation and Maintenance, Warranty

CGH562 specifications

The Cadet CGH562 is a robust and versatile aircraft, specifically designed for flight training and civilian aviation needs. As part of the Cadet series, it promises reliable performance and advanced features that cater to both novice pilots and seasoned aviation professionals.

One of the main features of the Cadet CGH562 is its advanced avionics suite. Equipped with a modern glass cockpit, the aircraft includes digital flight displays that provide real-time data about speed, altitude, and navigation. This enhances situational awareness for the pilot and allows for easier decision-making during flight. The inclusion of a multi-function display streamlines various functions, making it user-friendly and less daunting for new pilots.

In terms of performance, the CGH562 is powered by a fuel-efficient engine that offers impressive thrust-to-weight ratios. This not only contributes to enhanced climb rates but also ensures lower operational costs, making it an economical choice for flight schools and private owners alike. The airframe is constructed with lightweight composite materials, which improve fuel efficiency without compromising durability.

The aircraft also features advanced safety systems. Equipped with a state-of-the-art autopilot system, it allows for hands-free operation during long flights or for practicing maneuvering skills under varying conditions. The integration of a terrain awareness and warning system (TAWS) enhances safety further by alerting pilots of potential ground proximity issues.

Another noteworthy characteristic of the CGH562 is its spacious interior. Designed with comfort in mind, the cockpit can accommodate two pilots with room for additional passengers or gear in the rear. The seating arrangement is ergonomically designed, ensuring a comfortable flying experience during extended training sessions. The noise-reduction technologies further enhance this, making for a quieter and more pleasant experience.

Overall, the Cadet CGH562 stands out as a premier choice for aviation training and recreational flying. With its cutting-edge features, fuel efficiency, and focus on safety, it embodies the perfect blend of technology and practicality, catering to the evolving needs of the aviation industry. Whether for flight schools or personal use, the Cadet CGH562 is an exceptional aircraft that truly elevates the flying experience.