Operating Instructions | Model NB0064 |
General Safety Information (Continued)
●Always assume the nailer contains nails. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of nails. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the nailer could result in death or serious per- sonal injury.
●Do not drive a
nail on top of other nails. The nail could glance and cause death or a serious punc- ture wound.
●Do not operate
or allow anyone
else to operate 
the nailer if any 
warnings or 
warning labels 
are not legible. Warnings or warning labels are located on the nailer maga- zine and body.
●Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, exam- ine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur.
Caution indicates ! CAUTION a potentially haz-
ardous situation which, if not avoided, MAY result in minor or moderate injury.
●Do not make any modifications to the tool without first obtaining written
approval from Campbell Hausfeld. Do not use the nailer if any shields or guards are removed or altered. Do not use the nailer as a hammer. Personal injury or tool
damage may occur.
●Avoid long extended periods of work with the nailer. Stop using the nailer if you feel pain in hands or arms.
● Always check that the Work Contact |
Element (WCE) |
is operating |
properly. A nail |
could acciden- |
tally be driven |
if the WCE is |
not working properly. Personal injury
may occur (See "Checking the Work Contact Element" Section).
●Disconnect air supply and release tension from the pusher before attempting to clear jams because fasteners can be ejected from the front of the nailer. Personal injury may occur.
NOTICE | Notice indicates |
important infor- |
mation, that if not followed, MAY cause damage to equipment.
●Avoid using the nailer when the magazine is empty. Accelerated wear on the nailer may occur.
●Clean and check all air supply hoses and fittings before connecting the nailer to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced.
●Air compressors providing air to the nailer should follow the require- ments established by the American National Standards Institute
Standard
Operating The Nailer
LUBRICATION
This nailer requires lubrication before using the nailer for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis.
NOTICE | The work surface | |
can become dam- | ||
|
aged by excessive lubrication. Proper lubrication is the owner’s responsibili- ty. Failure to lubricate the nailer prop- erly will dramatically shorten the life of the nailer and void your warranty.
1. | Disconnect the |
|
| air supply from |
|
| the nailer to |
|
| add lubricant. |
|
2. | Turn the nailer | OIL |
| so the air inlet | |
|
| |
| is facing up. |
|
| Place |
|
| of 30 W non- |
|
| detergent oil into air inlet. Do not | |
| use detergent oils, oil additives, or | |
| air tool oils. Air tool oils contain sol- | |
| vents which will damage the nailer's | |
| internal components. | |
3. After adding oil, run nailer briefly. Wipe off any excess oil from the cap exhaust.
Recommended Hookup
Quick |
| Quick |
| Quick Plug |
|
|
| Regulator | ||||||||||||||
|
| (Optional) |
| Oiler |
|
|
|
| ||||||||||||||
Plug | Coupler |
|
|
|
| |||||||||||||||||
|
|
| ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Quick
Coupler
(Optional)
Air
Hose
Filter
www.chpower.com
3
