See Warranty on page 4 for important information about commercial use of this product.
Operating Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
BUILT TO LAST
Air Powered
Rivet Gun
Description
Professional air powered rivet guns are air tools designed for riveting a variety of materials, and can be used with up to 3/16" steel rivets.
Unpacking
When unpacking this product, carefully inspect for any damage that may have occurred during transit.
General Safety
Information
This product is part of a high pressure system and the following safety precautions must be followed at all times along with any other existing safety rules.
1. Read all manuals included with this product careful-
MANUAL
ly. Be familiar with the controls and the proper use of the equipment.
2.Only persons well acquainted with these rules of safe operation should be allowed to use the air tool.
Do not exceed the
! CAUTION maximum
operating pressure of the air tool (90 PSI). This can reduce the life of the tool.
3.Do not exceed any pressure rating of any component in the system.
4.Disconnect the air tool from the air supply before changing tools or attachments, servicing, and during
! WARNING
Safety glasses and ear protection must be worn during operation.
5.Do not wear loose fitting clothing, scarves, neck ties or jewelry when operating any tool. Loose clothing or jewelry may become caught in moving parts and result in serious personal injury.
6.Do not depress trigger when connecting the air supply hose.
7.Always use nose pieces designed for use with air powered tools. Do not use damaged or worn attachments.
8.Never trigger the tool when not applied to a work object. Attachments must be securely attached. Loose attachments can cause serious injury.
9.Protect air lines from damage or puncture.
10.Never point an air tool at oneself or any other person. Serious injury could occur.
11.Check air hoses for weak or worn condition before each use. Make sure all connections are secure.
!WARNING
Release all pressure from the system before attempting to
install, service, relocate or perform any maintenance.
12.Keep all nuts, bolts and screws tight and ensure equipment is in safe working condition.
13.Do not put hands near or under moving parts.
14.Always secure workpiece in a vise or clamp. Do not place hands on the back cylinder when operating the tool.
Never operate the ! WARNING rivet gun without
the safety cap installed. Personal injury can occur if the rivet gun is operated without the safety cap (SV825800AV) installed.
Excessive exposure
! WARNING to vibration, working in awkward positions and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling or pain occur and consult a physician.
Assembly
SYSTEM SETUP
PLEASE REFER TO AIR TOOL AND SPRAY GUN
Using fittings or air hoses which are too small can create a pressure drop which will result in a loss of power in the tool.
NOTE: Do not install a quick coupler set between the tool and whip hose.
Before tool is connected to air, attach safety cap to gun by tightening frame cap nut to back of gun.
Pre-Operation
LUBRICATION
Air tools require lubrication throughout the life of the tool. Proper lubrication is the owner’s responsibility. Use Campbell Hausfeld air tool oil (Part No. ST127000AV) to lubricate, clean and inhibit rust in one step. Failure to lubricate and maintain the air tool properly will dramatically shorten the life of the tool and will void the warranty.
This rivet gun
! CAUTION requires lubrica- tion before initial use and before and after each additional use.
Disconnect the
! WARNING rivet tool from the air supply before lubricating.
1. Turn the rivet gun on it's side so that the air inlet is facing up.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2003 Campbell Hausfeld/Scott Fetzer | For parts, product & service information | IN243801AV 2/03 |
visit www.chpower.com
