Operating Instructions |
|
|
| SB660000 | |
Operating Instructions | 5. | Depress the WCE |
| 3a. For 18 gauge nails, insert a stick | |
(Continued) |
| against the work |
| of Campbell Hausfeld nails or | |
Operational Mode - Single Cycle |
| surface without |
| equivalent (see “Fasteners” section) | |
| pulling the trigger. |
| into the magazine against the | ||
| Always know the |
|
| ||
|
| The tool must not |
| ribs. Make sure the pointed ends | |
| operational mode of |
|
| ||
the tool before using. Failure to know |
| operate. Do not use the tool if it | of the fasteners are resting on the | ||
the operational mode could result in |
| operates without pulling the trigger. | bottom ledge of the magazine when | ||
death or serious personal injury. |
| Personal injury may result. |
| loading. Make sure the nails are not | |
|
|
|
| ||
This tool requires the trigger to be | 6. Remove the tool from |
| dirty or damaged. | ||
pulled each time a nail is driven. The |
|
| |||
| the work surface. |
|
| ||
nailer can be actuated by depressing the |
|
|
| ||
| The WCE must return |
|
| ||
Work Contact Element (WCE) against |
|
|
| ||
| to its original down |
|
| ||
the work surface followed by pulling |
|
|
| ||
| position. The tool |
|
| ||
the trigger. |
|
|
| ||
| must not operate. Do not use the |
| |||
|
|
|
| ||
The trigger must be released to reset |
| tool if it operates while lifted from |
| ||
the tool before another nail can be |
| the work surface. Personal injury |
| ||
driven. |
| may result. |
|
| |
|
| 7. | Pull the |
| 3b. For 16 gauge nails, insert the nail |
|
|
| trigger |
| |
|
|
|
| points down into the slot next to the | |
|
|
| and |
| |
|
|
|
| rail. | |
|
|
| depress |
| |
|
|
|
|
| |
|
|
| the WCE |
|
|
|
|
| against |
|
|
Work contact element (WCE) |
| the work surface. The tool MUST |
| ||
| NOT operate. |
|
| ||
| Check the operation |
|
|
| |
| 8. | Depress |
|
| |
| of the Work Contact |
|
| ||
Element (WCE) trip mechanism before |
| the WCE |
|
| |
each use. The WCE must move freely |
| against |
|
| |
without binding through its entire |
|
| Magazine Rail | ||
| the work |
| |||
travel distance. The WCE spring must |
|
|
| ||
| surface. |
|
| ||
return the WCE to its fully extended |
|
| 3c. For staples, load a clip of staples | ||
| Pull the |
| |||
position after being depressed. Do |
|
| with the crowns straddling the | ||
not operate the nailer if the WCE trip |
| trigger. The tool MUST operate. | |||
| magazine rail. | ||||
mechanism is not operating properly. |
|
|
| ||
| An improperly |
| |||
Personal injury may occur. |
|
| |||
| functioning tool |
| |||
1. | Disconnect the air |
|
| ||
must not be used. Do not actuate the |
| ||||
| supply from the tool. | tool unless the tool is placed firmly |
| ||
|
| against the work piece. |
|
| |
2. | Remove all fasteners | Loading/Unloading The Nailer |
| ||
| from the magazine | 1. Always disconnect the tool from the |
| ||
| (see Loading/ |
| air supply before loading fasteners. |
| |
| Unloading). | 2. | Push | Latch | Magazine Rail |
|
|
| |||
3. Make sure the trigger |
| down on | Button | 4. Push the magazine cover forward | |
| and WCE move freely |
| the latch |
| until latch button pops up. |
| up and down without |
| button. |
|
|
| sticking or binding. |
| Pull back |
|
|
4. | Reconnect air supply |
| on the |
|
|
| magazine |
|
| ||
| to the tool. |
|
|
| |
|
| cover. |
|
| |
|
|
|
|
| |
5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except that you must disconnect the air supply before unloading.
5 | www.chpower.com |