The machine is noisy.

• There will always be some motor, pump and drum noise during spin.

GB

 

 

 

The machine wont spin properly.

• Out of Balance detected when attempting to go into a spin cycle - If this

 

 

 

happens the machine will continue to try to repeat the distribution of the load

 

 

required before the machine will go into higher spin speeds - This will increase

 

 

the programme time accordingly. This is a safety feature to prevent damage.

 

 

Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,

 

 

etc). - Try the programme again using a different load.

The machine leaks from the dispenser.

•The dispenser drawer is blocked with detergent and requires cleaning.

•The water pressure is too high and requires turning down - turn down the tap on the water supply pipe slightly and try again.

•The machine is tilting forwards - It must be level when in its final position.

The machine leaks (other than dispenser).

•The fill hose is loose, check both the cabinet and tap ends.

•The fill hose is tight but still leaks, if so replace the rubber washers, or the fill hose is missing the rubber washer.

•The drain hose is not fixed in properly.

The indicator lights on the console are flashing rapidly.

The machine smells.

The machine door cannot be opened.

Door Seal damaged at the bottom.

The water level is too low when the machine is washing.

There is too much foam.

•Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again If the problem persists contact the Technical Assistance Service.

•The machine requires a service wash. Run a 90 degree wash cycle with deter- gent and no laundry.

•The door will not open until the door lock indicator light goes out shortly after the program has finished.

•The door seal has drainage holes at the bottom - This is normal.

•The water level is correct if it can be seen at the bottom of the door.

•The detergent is not suitable for machine washing (it should display the text

‘for washing machines’ or ‘hand and machine wash’ or the like).

•Too much detergent was used - less detergent is required in soft water.

After completing the programme, or before starting a programme, the machine has turned itself off (no lights).

General.

•To comply with new energy saving regulations the machine is fitted with an automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate the machine, it can then either be switched off or a new programme selected.

•Your washing machine contains sensors that monitor progress during the wash cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro- gress).

Normally, if your machine successfully completes the cycle, there is unlikely to be anything wrong!

Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.

14

Page 13 Page 15
Page 14
Image 14
Cannon IWD manual Etc. Try the programme again using a different load
Page 13 Page 15

IWD specifications

Cannon IWD, a modern advancement in the field of industrial and commercial manufacturing, represents a significant evolution in in-line bulk supply systems. Primarily designed for the efficient mixing and dispensing of materials, Cannon IWD is particularly advantageous for applications in industries such as automotive, aerospace, and construction.

One of the main features of the Cannon IWD is its versatility. It can handle a wide variety of materials, ranging from polyurethanes to epoxies, and can be adapted to meet the specific requirements of diverse manufacturing processes. This adaptability ensures that manufacturers can optimize their operations, reduce waste, and improve overall productivity.

The technology employed in the Cannon IWD integrates precision dosing systems that utilize advanced control algorithms. These algorithms ensure accurate measurement and mixing of raw materials, allowing for consistency in production quality. This precision extends to the temperature control systems integrated into the design, which are critical for maintaining the properties of various materials. This level of control minimizes batch-to-batch variability, leading to uniformity in the end product.

Another characteristic of the Cannon IWD is its user-friendly interface. Operators can easily monitor and adjust settings through a digital display, which enhances operational efficiency and reduces the likelihood of human error. The system is designed for quick setup and easy maintenance, allowing manufacturers to minimize downtime and maximize output.

Moreover, safety is a top priority in the design of the Cannon IWD. Equipped with several fail-safes and emergency shut-off systems, it ensures that operators can work safely without the risk of dangerous material leaks or equipment malfunctions.

Cannon IWD also emphasizes sustainability, with features designed to reduce energy consumption and material waste. By optimizing the mixing process, the system allows for the reduced use of raw materials while still ensuring high-quality outputs, aligning with eco-friendly manufacturing practices.

In summary, Cannon IWD stands out as a robust, efficient, and sustainable solution for the industrial sector. Its innovative technologies, user-centric design, and commitment to safety make it an invaluable asset for businesses looking to enhance their production capabilities in an increasingly competitive market.
Top Page Image Contents