Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

 

GB

that the problem cannot be solved easily using the following list.

 

 

 

Problem:

The machine does not switch on.

The wash cycle does not start.

The machine does not fill with water or “H2O” will flash on the display.

Possible causes / Solutions:

•The appliance is not plugged into the socket fully, or not enough to make contact.

•There is no power to the socket, or the fuse has blown in the mains plug.

•The door is not closed properly.

•The ON/OFF button has not been pressed.

•The START/PAUSE button has not been pressed.

•The water tap has not been turned on to allow water to flow into the machine.

•A delayed start has been set.

•The water inlet hose is kinked.

•The water inlet hose is not connected to the water supply.

•The water pressure is too low.

•The water tap has not been turned on to allow water to flow into the machine.

•There is no water supply to the house.

•The inlet valve filter is blocked.

•The START/PAUSE button has not been pressed.

The machine continuously fills with water and continually drains away or Water left in the drum

or Stuck on wash.

•The top of the drain hose is too low - It must be fitted at a height between 65 and 100 cm from the floor (see “Installation”).

•The drain hose is connected incorrectly to the sink trap allowing water to run into the machine, the drain hose must be positioned higher than the bottom of the sink to prevent water flowing down the drain hose.

•The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

The machine does not drain or spin or F05 error code in the display.

•The Pump filter is blocked.

•The drain hose is kinked (see “Installation”).

•New Installation - The blanking cap or spigot has not been removed if connected under a sink.

•The drain hose or sink trap is blocked.

•The wash cycle does not include draining, some wash cycles require the drain phase to be started manually.

•The ‘Spin Speed’ selector knob is in the “” position.

The machine does not heat or poor wash results.

The programme takes too long or The Display changes the estimated ‘Time to End’ during the programme.

The machine vibrates a lot during the spin cycle.

•The ‘Temperature’ selector knob is in the “” position.

•Programme times will vary due to water pressure, the incoming water tempera- ture and if the wash load goes out of balance. This will increase the programme times accordingly (see ‘ The machine wont spin properly’ below).

•The feet have not been adjusted, enabling the machine to rock.

•New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

•The machine is trapped between cabinets and/or walls.

•The load is in a slight out of balance condition and machine is spinning, but at a lower speed.

13

Page 12 Page 14
Page 13
Image 13
Cannon IWD manual Troubleshooting, Problem, Possible causes / Solutions
Page 12 Page 14

IWD specifications

Cannon IWD, a modern advancement in the field of industrial and commercial manufacturing, represents a significant evolution in in-line bulk supply systems. Primarily designed for the efficient mixing and dispensing of materials, Cannon IWD is particularly advantageous for applications in industries such as automotive, aerospace, and construction.

One of the main features of the Cannon IWD is its versatility. It can handle a wide variety of materials, ranging from polyurethanes to epoxies, and can be adapted to meet the specific requirements of diverse manufacturing processes. This adaptability ensures that manufacturers can optimize their operations, reduce waste, and improve overall productivity.

The technology employed in the Cannon IWD integrates precision dosing systems that utilize advanced control algorithms. These algorithms ensure accurate measurement and mixing of raw materials, allowing for consistency in production quality. This precision extends to the temperature control systems integrated into the design, which are critical for maintaining the properties of various materials. This level of control minimizes batch-to-batch variability, leading to uniformity in the end product.

Another characteristic of the Cannon IWD is its user-friendly interface. Operators can easily monitor and adjust settings through a digital display, which enhances operational efficiency and reduces the likelihood of human error. The system is designed for quick setup and easy maintenance, allowing manufacturers to minimize downtime and maximize output.

Moreover, safety is a top priority in the design of the Cannon IWD. Equipped with several fail-safes and emergency shut-off systems, it ensures that operators can work safely without the risk of dangerous material leaks or equipment malfunctions.

Cannon IWD also emphasizes sustainability, with features designed to reduce energy consumption and material waste. By optimizing the mixing process, the system allows for the reduced use of raw materials while still ensuring high-quality outputs, aligning with eco-friendly manufacturing practices.

In summary, Cannon IWD stands out as a robust, efficient, and sustainable solution for the industrial sector. Its innovative technologies, user-centric design, and commitment to safety make it an invaluable asset for businesses looking to enhance their production capabilities in an increasingly competitive market.
Top Page Image Contents