Start Here
Easy Setup Instructions
READ THIS SHEET FIRST
Thank you for purchasing the Canon PIXMA MP760. To prepare your machine for use, please follow these Easy Setup Instructions before referring to any other documentation.
IMPORTANTDo not connect the USB cable until after the software is installed. See the rear side of this sheet for details.
1Unpack and install the machine.
Check the package contents.
• Machine | • Power cord |
| • Print head |
Do not touch!
Click
Lower the lock lever until you hear a click as it locks into place.
MP760 |
|
|
• Ink tanks |
|
|
Black | Black | |
| Cyan | |
| Magenta | |
| Yellow | |
• Easy Setup Instructions | • Quick Start Guide |
|
The Setup
A printer cable is not included. You must purchase a USB cable (less than 10 ft./3 m) to connect your machine to a computer.
2Connect the power cord.
1Connect the power cord.1.Connect one end of the power cord to the rear of the machine.2.Connect the other end to the AC outlet.2If the message <There is no print head installed. Install the print head.> appears, go to Step 4, "Install the print head."
3Load the paper.
1Open the Paper Support, then pull out the extension.2Load a few sheets of(1) Open the Paper | Pinch and adjust | Load the paper with the print side face up. | |
Support. | |||
the paper guide |
| ||
|
| ||
| to the width of |
| |
| the stack. |
|
(2) Pull out the extension | Ensure the paper stack | |
does not exceed the paper | ||
until it stops. | ||
limit mark. | ||
|
4Install the print head.
5Install the ink tanks.
1Prepare the ink tanks.Remove the | Remove the protective cap |
protective film. If it is not | and discard it. |
removed completely, |
|
problems with printing |
|
may occur. |
|
| Do not touch! |
Click
Press down until the ink | Good example | Bad example. Tank 6Bk is |
tank clicks into place. |
| not fully inserted. Make |
|
| sure to press it down until |
|
| you hear a click. |
| Click |
Click | Pull the Scanning Unit Lever |
| towards you to close the |
| Scanning Unit. |
Close the two Inner Covers. | IMPORTANT |
Be sure to hold the Scanning Unit firmly with one hand. |
6Align the print head from the Operation Panel.
Be sure to align the print head to ensure print quality.1Press [OK] to start print head alignment.(1) This message appears. | (2) Press [ ] to select <Yes>. | (4) The machine will print |
|
| the print head position |
|
| pattern and automatically |
|
| align the print head. |
1Ensure that the Paper Output Tray is open. Then lift the Scanning Unit (Printer Cover) until it locks into place.
IMPORTANT
Be sure to hold the Scanning Unit firmly with one hand.Click
(2)Pull the Scanning Unit Lever.If this message | (3) Press [OK]. | |
does not appear | ||
| ||
after closing the |
| |
Scanning Unit, |
| |
see "Aligning |
| |
The Print Head |
| |
Automatically" |
| |
in the Quick Start |
| |
Guide. |
|
If the printed pattern matches the illustration, print head alignment is complete.
You can change the language displayed on the LCD.
2 Remove shipping tape from the | 3 Raise the lock lever. |
Inner Cover and Open Both Inner |
|
Covers. |
|
The Print Head Holder moves to the center. | Touch only the lock lever! |
Do not touch the Print Head Holder while it is |
|
moving. |
|
| Raise lock lever |
| completely. |
Inner Covers |
|
Hardware setup and print head alignment is complete.
If you are connecting the machine to a computer for use, see the rear side of this sheet for instructions on installing the software.
Canon and BCI are registered trademarks and PIXMA is a trademark of Canon Inc. in the United States and may also be registered trademarks or trademarks in other countries.
All other products and brand names are registered trademarks or trademarks of their respective owners. Specifications subject to change without notice.
© CANON INC. 2004 | PRINTED IN CHINA |