Carrier 33CS owner manual Scheduleoccupiedmode, Programming Schedules Unlike many other

scheduleoccupiedmode

fellow schedule				_	auto		_	off
held				_	on		_	heat
_,- holiday						o/,_	_-	cool
check UV light						_	!_-	Em heat
set...check hum pod						[]	3	sec to
							p[ess done
check filter				actual	temp		cancel alert
...clock ...calendar ...dailyschedule						...holiday		settings
				700		auxiliary				A
ll_ TU	_.	ooc		oteside	temp	heat on			1
_We	_o		star[at		returnon		heat	cool
Th	--	occ3	temporaryholdf ....				tat:	setat:	r
2				...................... ......

right corner on the screen, depending on the mode the system is in. If it is the first time the thermostat is being used, the "heat"

indicator will be displayed. The preprogrmmned heating or cooling temperatures are displayed in a box at the bottom of the screen. Change the displayed temperature set point by pressing the up or down buttons until the desired setting is reached.

To change other temperature set points, press the mode but- ton. The arrow will move to the next mode and the screen will

show the related temperature set point in a box. Then press the up or down buttons to change the displayed set point.

When there are arrow indicators next to both of the heat and cool indicators, the heating and cooling set points are both dis- played at the bottom of the screen. The user can change either one by pressing the soft button underneath the set point to be changed. Press the up or down buttons to adjust the tempera-

©<-b©dbdb©

soft keys

V

rare. Repeat the process for the other set points if necessary. Press the done button when finished.

The thermostat will hold these changes for two hours or un-

Fig. 2 -- Thermostat Front Panel Buttons

UP BUTTON -- This button is used to increment the current- ly chosen value (temperature, clock, calendar, etc.).

DOWN BUTTON- This button is used to decrement the currently chosen value (temperature, clock, calendar, etc.).

"SOFT" BUTTON -- There are 6 soft buttons (or keys). The soft buttons are used to select the onscreen indicator directly above that specific button. These indicators can change based on the actions of the user.

Set Time and Date --The user must set the time and date before the thermostat's progralmning features can be used. Perform the following procedure:

1.Open the thermostat front panel door.

2.Press the set button. The screen will show the word "clock" on the left of the display and the thne will be shown on the bottom. Press the set button again.

3.To set the correct hour, press the soft button underneath the hour indicatoc and then press the up or down buttons to adjust the value.

4.To set the correct minutes, press the soft button under- neath the minutes indicatoc and then press the up or down buttons to adjust the value.

5.To set the correct date, press the set button until the screen

displays the word "calendar" and the date is shown on the bottom of the screen.

6.To set the correct month, press the soft button underneath the letter M (month), and then press the up or down but- tons to adjust the value.

7.To set the correct day of the month, press the soft button underneath the letter D (day), and then press the up or down buttons to adjust the value.

8.To set the correct year, press the soft button underneath the letter Y (year), and then press the up or down buttons to adjust the value.

9.Press the done button to finish.

10.Close the thermostat door.

Setting or Changing Heating and Cooling Set

Points -- The Edge (RPro thermostat is installed with preset

heating and cooling temperature settings. The user can use these settings or change them. The user can also temporarily

change the temperature from the progralmned set points.

To temporarily hold the temperature for two hours, perform

the following. Open the front thermostat door. An arrow will be displayed next to the words "off," "heat," or "cool" in the upper

til the next progralmned cycle begins. The words "temporary hold" will be displayed while this is in effect. To change the amount of thne that the temperature is on hold, press the soft button under the hold hours or minutes indicators. Then press

the up or down buttons to adjust the time hold time. Close the door when done.

Holding Temperature Set Points --The user can

ovemde the progralruned temperature settings and hold the

temperature at a specific setting without the temperature changing during the next progralmned period. To ovemde the temperatures, perform the following:

1.Open the door.

2.Press the schedule button. The arrow will move to the hold indicator.

3.The screen will display the set point temperature. To change the set point temperature, press the up or down

buttons. The temperature will stay at the new setting until it is released from the hold.

4.To change the heating set point when the cooling set

points are displayed (and vice versa), press the mode but- ton until the arrow moves to the desired mode. Press the

up or down buttons to change the set point.

5.To return the temperature to the preset level for that time period, press the schedule button until the arrow moves to the following schedule indicator.

6.Close the door.

Programming Schedules _ Unlike many other

thermostats, the Edge Pro thermostat gives the user the option of progrmr_ning every day of the week differently. The ther-

mostat is preprogralmned at the factory with the same settings

for all seven days. See Table 1.

Table 1 -- Schedule Factory Settings

	START	HEAT SET	COOL SET
PERIOD	TIME	POINT	POINT
Occ	6 AM	68	78
Occ2	8 AM	68	78
Occ3	3 PM	68	78
Unocc	6 PM	60	85

To set up a different schedule where all the days are the same, perform the following:

1.Open the thermostat door.

2.Press the set button until the screen displays "daily sched- ule" in the center of the screen. The list of the days of the week are displayed on the left. The arrows next to each day indicate that all seven days will be progralmned the same way.