Carvin PickupWiring manual Dual-Single Coil Switch Wiring, Kit, TL60-33

CARVIN PICKUP WIRING INSTRUCTIONS

LOCATING PICKUPS ON THE GUITAR

Determine where you want to locate your pickup(s). Then find the center line of the neck and draw a center line on the body. Use the paper template on the back of this sheet to locate the routing and the pickup mounting screw holes.

DRILLING PICKUP WIRE HOLE

If you are mounting the pickup directly on a wood body, you must drill a hole for the pick- up wire. Use a 3/16” or 1/4” drill bit. If you have to drill through more than 2” of wood, you should use a special 12” long drill bit, which is available at most hardware stores.

PICKUP WIRING

All Carvin 22 series pickups have three wires plus a bare shield wire. The shield wire always goes to ground. The white wire only gets used if you want dual-to-single coil switching. If you don’t want to use this feature, then tape the white wire back. The black and red wires are to be used for standard humbucking operation. Solder red to hot and black to ground. If your guitar sounds out of phase with both pickups on, reverse the red and black wires of one pickup.

WIRING THE CONTROLS

If you are using one of the Carvin circuits, just follow the desired wiring diagram. You should install a ground wire that runs from the tailpiece or bridge to the control area. Solder this ground wire to the back of one of the potentiometers. Be careful not to use excessive heat when soldering to the potentiometers or switches as you may damage them.

PHASE SWITCH WIRING

A phase switch can be wired into any two or three pickup guitar. As the diagram below shows, only one pickup is hooked up to the phase switch. The phase switch will only function when another pickup is used in conjunction with the pickup that is switched out of phase. The phase switch will give a nasal muted type sound with slightly less output.

Note: Solder green and white wires together unless otherwise specified. For pickups that do have the green wire disregard this note.

TOP COIL A

R

W

B

G

BOTTOM COIL BRED and WHITE wires: Coil A

BLACK and GREEN wires: Coil B

Dual-Single Coil Switch Wiring

To obtain humbucking operation when playing through both pickups in the single coil mode, wire one humbucking pickup using fig 1 and the other pickup with the diagram in fig 2 (also see Kit 40 DC127 diagram). Neck pickup coil A together with bridge pickup coil B sounds more like a telecaster. Neck pickup coil B & bridge pickup coil A together sound more like a Stratocaster.

Fig 1. Coil “A” on in single coil mode.

PICKUP		GRN
		WHT
					SERIES/PARALELL
	RED	BLK					G
SHIELD			S3		W		R
TO	HOT TO VOLUME			TO	B	HOT OUT
GROUND	OR SELECTOR SW.			GROUND
Fig 2. Coil “B” on in single coil mode.						TO
PICKUP		GRN			G	HOT OUT
		WHT
	BLK	RED	S3
SHIELD
				HOT OUTPUT	W	BLK & SHLD
				TO VOLUME

PHASE SWITCH WIRING

W

G

PICKUP	RED
SHIELD	BLK
TO	HOT OUTPUT
	TO VOLUME
GROUND	OR SELECTOR

S3

TO

GROUND

	OR SELECTOR	to GRND	R
		SERIES/SPLIT/PHASED
TO GROUND
		ON/ON/ON

Fig 3. This wiring gives you three different sounds.

1.Top single coil, 2. dual coil humbucking or 3. bottom single coil. (As used on the TL60-33 circuit)

PICKUP		S2	HOT OUTPUT
	RED		TO VOLUME
	WHT		OR SELECTOR
	GRN		TO
SHIELD	BLK
			GROUND

KIT 30

Single pickup guitar with volume, tone & coil splitter.

KIT 40 DC127 (includes 2 coil splitters)

For 2 Pickup guitar. (Used on the Carvin DC127 model)

76-00015

KIT 40

2 Pickup guitar with a 3-way pickup selector, 1 volume & 1 tone

TL60-33

For 2 Pickup guitar. With 3-way Pickup Selector (S4) & 3-way Coil Splitter Switch (S2).

NECK			PICKUPBRIDGE
PICKUP
		S
			R B
R B S		S2	W
P1	P2		Single
	TONE		Dual
VOL			Single

C1

GND

S4
SWITCH	L11
	JACK