Module No.
2307/2335/2355/2357
GENERAL GUIDE
•Press C to change from mode to mode.
•Holding down C in any mode for about one second returns to the normal timekeeping screen.
•Pressing C after performing some operation in the Recall Mode, Alarm Mode, or Countdown Alarm Mode returns to the normal timekeeping screen.
•The configuration of your watch may differ somewhat from that shown in the illustration.
| Timekeeping Mode |
| ||
A | B | Press D. | ▼ | 6 |
| ||||
|
|
| ||
|
|
|
| Press C. |
|
|
|
| Press D. |
1008 |
| ▼ |
| ▼ |
C | D |
|
| |
|
|
| ||
|
| Press D. |
| 6 |
▼
Press C.
Stopwatch Mode
▼ | 00OO |
S
▼
Press C.
Countdown Alarm Mode
▼ | 00OO | ▼ |
A |
| Press C. |
TIMEKEEPING MODE
•Pressing D changes the display in the sequence shown below.
|
|
|
| Day of week |
|
|
|
| Month – Day |
A | B |
| Press D. |
|
|
|
| ▼ | 630 |
| 1008 |
| Crown | Press D. |
C | D | ▼ |
| |
|
| |||
| Seconds |
| ▼ | |
| Press D. |
| ||
| Hour : Minutes | 630 | ||
|
|
|
PM indicator
Month – Day
Barometric pressure graph *See “BAROMETER MODE”.
•The display type you select is used until you change it.
•Pressing B in any mode besides the Countdown Alarm Mode or Stopwatch Mode illuminates the display for about 1.5 second. The backlight is disabled while a setting screen is on the display.
•For Module 2307 and 2357, the backlight illuminates both the digital display and analog face. For Module 2335 and 2355, the backlight illuminates the digital display only.
•If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.
•If you do not perform any operation for about 10 hours in the Barometer Mode, Altimeter Mode, or Thermometer Mode, the watch automatically reverts to the Timekeeping Mode screen.
Barometer Mode |
| Altimeter Mode |
|
| Press |
|
|
| C. |
|
|
▼ | ▼ | ▼ | 1250 |
8AA0 |
| AL |
|
|
|
| |
▼ |
| Press C. | |
1013 |
| ▼ |
|
|
|
| |
|
| Thermometer Mode | |
|
| ▼ | 185 |
|
| ENP |
|
Alarm Mode |
|
|
|
|
| Press C. | |
A L |
| ▼ |
|
|
| Recall Mode |
|
▼ | ▼ |
|
|
| ▼ | 1250 | |
7OO | Press | AEC |
|
| C. |
|
|
• When the
• While any other setting is selected (flashing), press D to increase the number or Bto decrease it.
• Holding down either button changes the setting at high speed.
4.After you set the time and date, press Ato change to the contrast setting screen.
•The indicator CNT appears on the left of the screen, and the value indicating the current contrast setting flashes on the right.
•You can set the contrast to one of 11 levels in the range of
5.Press D to make the display darker, or Bto make it lighter.
6.After the contrast is the setting you want, press Ato return to the normal timekeeping screen.
•The day of the week is automatically set in accordance with the date.
•The date can be set within the range of January 1, 1995 to December 31, 2039.
•The watch’s
To set the time and date
1.While in the Timekeeping Mode, hold down A until the seconds digits flash on the display.
2.Press C to move the selection (flashing) in the following sequence.
Seconds Hour Minutes
12/24
| Day |
|
| Month |
|
| Year |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
3.While the seconds setting is selected (flashing), press Dto reset it to 00. If you press D while the seconds setting is in the range of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If the seconds setting is in the range of 00 to 29, the minutes count is unchanged.
•While the
To set the analog time
1. Pull the crown out to stop the second hand.
•If you plan to restart analog timekeeping on some time signal (from the radio or television), pull the crown out when the second hand is at the 12 o’clock position.
2.Set the hands by turning the crown.
3.Push the crown back in to restart timekeeping.
•Analog time is kept by a mechanical timepiece. Because of this, the second hand may not start to move exactly when you push the crown back in.