RECALL MODE
Recalling data
1.Use Cto enter the Recall Mode.
2.Each press of D cycles through the barometric pressure, altitude, and temperature data in memory. Mode indicators appear to tell you what type of data is currently displayed.
•Note that measurement units are not indicated on the Recall Mode screens.
•The display shows “- - - - –
| 1 second |
A | B later |
| ▼ | 12 | 50 |
|
| ||
| AEC |
| Memory number |
C | D |
| |
|
| ||
| Altitude | ||
Recall Mode indicator |
|
| |
COUNTDOWN ALARM MODE
The countdown alarm can be set within a range of 10 seconds to 60 minutes. When the countdown reaches zero, an alarm sounds for 10 seconds or until you press any button.
1 second
AB later
| ▼ | 00OO |
| A | 1/10 second |
C | D | Seconds |
Countdown Alarm Mode indicator | Minutes | |
| ||
To set the countdown start time and auto repeat function on and off
1. Hold down A while in the Countdown Alarm Mode. The minutes setting |
flashes on the display because it is selected. |
Deleting Data
CLA
While in the Recall Mode, hold down A. The watch beeps, and the message CLR flashes on the display to indicate data is about to be deleted. Keep A depressed for about two seconds to delete all the measurement data currently in memory.
•Note that this procedure deletes all measurement data in memory. You cannot delete individual records.
2. Press Cto change the selection in the sequence shown below. |
|
| Minutes |
|
| Seconds |
|
| Auto repeat ON/OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3.Press D to increase the selected setting or B to decrease it. Holding down either button changes the setting at high speed.
•The seconds can be set in units of 10 seconds.
•Set 0 minutes, 0 seconds to specify a start time of 60 minutes.
•While the AUTO ON/OFF setting is selected (flashing), press D or B to toggle auto repeat on and off.
4.After you set the countdown start time and auto repeat ON/OFF setting, press A to return to the Countdown Alarm Mode screen.
ALARM MODE
When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the preset time each day. Press any button to stop the alarm after it starts to sound.
When the Hourly Time Signal is turned on, the watch beeps every hour on the hour.
Alarm time
1 second
AB later
|
| ▼ | 7OO |
A L |
|
| Hourly time signal on |
C | D |
| indicator |
|
|
| |
Alarm Mode indicator |
|
| Alarm on indicator |
To set the alarm time
1.Hold down A until the hour digits start to flash on the display. The hour digits flash because they are selected. At this time the alarm is automatically turned on.
2.Press C to change the selection in the sequence shown below.
Hour 
Minutes
3. Press D to increase the number or B to decrease it.
•Holding down either button changes the setting at high speed.
4.After you set the alarm time, press A to return to the Alarm Mode screen.
• The format
select for normal timekeeping.
• When setting the alarm time using the
To stop the alarm
•Press any button to stop the alarm after it starts to sound.
To turn the Daily Alarm and Hourly Time Signal on and off
Press Dwhile in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal in the sequence shown below.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Both ON |
|
| Both OFF | Daily Alarm only Hourly Time | ||||||
|
|
|
|
|
|
|
|
|
|
| Signal only | |
|
|
|
|
|
|
|
|
|
|
|
|
|
•The alarm and hourly time signal indicator is displayed in all modes.
To test the alarm
Hold down Dwhile in the Alarm Mode to sound the alarm.
| Auto repeat ON | Auto repeat OFF |
10OO | 10OO |
Auto repeat ON indicator
To use the countdown alarm
1.Press D while in the Countdown Alarm Mode to start the countdown alarm operation.
2.Press Dagain to stop the countdown alarm operation.
•You can resume a paused countdown alarm operation by pressing D.
3.Stop the countdown alarm and then press Bto reset the countdown time to its starting value.
•When the end of the countdown is reached and auto repeat is off, the alarm sounds for 10 seconds or until you stop the alarm by pressing any button. Countdown timing stops and the countdown time is automatically reset to its starting value after the alarm stops.
•When the end of the countdown is reached while auto repeat is on, the alarm sounds, but the countdown restarts from the beginning without stopping. You can stop the countdown by pressing D and manually reset to the start time by pressing B.
•When the start time is less than one minute and auto repeat is turned on, the countdown alarm tone sounds for only one second instead of the normal 10 seconds.
STOPWATCH MODE
The Stopwatch Mode lets you record elapsed time, split times, and two finishes. The range of the stopwatch is 59 minutes, 59.99 seconds. Stopwatch functions are available in the Stopwatch Mode, which you can enter using C.
|
| 1 second |
|
|
|
| A | B later |
|
|
|
|
| ▼ | 00OO |
| |
| S |
|
| 1/100 second | |
| C | D |
| Seconds |
|
|
|
|
|
| |
| Stopwatch Mode indicator | Minutes |
| ||
| (a) Elapsed time measurement |
|
|
| ||
D | ▼ D | ▼ D |
| ▼D | ▼ B |
| Start | Stop |
| Stop | Clear | |
| (b) Split time measurement |
|
|
| ||
D | ▼ B | ▼ B |
| ▼D | ▼ B |
Start | Split | Split release |
| Stop | Clear |
| (c) Split time and |
|
|
| ||
D | ▼ B | ▼ D |
| ▼B | ▼ B |
Start | Split | Stop |
| Split release | Clear |
| First runner | Second runner finishes. | Record time of |
| |
| finishes. | Record time of first runner. | second runner. |
| |