Operation Guide 3085

World Time

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use Dto select the Hourly Time

City code

Current time in the zone of the selected city code

World Time shows the current time in 48 cities (29 time zones) around the world.

•All of the operations in this section are performed in the World Time Mode, which you enter by pressing C.

To view the time for another city code

In the World Time Mode, press Dto scroll eastwardly through city codes.

•For full information about city codes, see the “City Code Table”.

•If the current time shown for a city is wrong, check your Timekeeping Mode time and Home City code settings and make the necessary changes.

Hourly time signal

Signal (

).

 

on indicator

2. Press A to toggle it on (

displayed) and off

 

 

(

displayed).

 

•Turning on the Hourly Time Signal displays the Hourly

Time Signal indicator on its Alarm Mode screen.

• While the Hourly Time Signal is turned on, the Hourly Time Signal on indicator is shown on the display in all modes besides the Alarm Mode.

On/Off status

Stopwatch

To toggle a city code time between Standard Time and Daylight Saving Time

DST indicator

1. In the World Time Mode, use D to display the city code

(time zone) whose Standard Time/Daylight Saving Time

 

 

 

setting you want to change.

 

 

 

2. Hold down Afor about one second to toggle between

 

 

 

 

 

 

Daylight Saving Time (DST indicator displayed) and

 

 

 

 

 

 

Standard Time (DST indicator not displayed).

 

 

 

• The DST indicator is on the display whenever you

 

 

 

display a city code for which Daylight Saving Time is

 

 

 

turned on.

• Note that the DST/Standard Time setting affects only the

currently displayed city code. Other city codes are not

affected.

• In the World Time Mode, you can switch the city code

you currently have selected as your Timekeeping Mode

Seconds

Minutes

1/100 second

The stopwatch lets you measure elapsed time, split times, and two finishes.

•The display range of the stopwatch is 59 minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.

•The stopwatch measurement operation continues even if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.

•All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.

Home City between Standard Time and DST. The

setting you select in the World Time Mode will also be

applied in the Timekeeping Mode.

Alarms

To measure times with the stopwatch

Elapsed Time

Start

Stop

Re-start

Stop

Clear

Split Time

 

 

 

 

Alarm time (Hour : Minutes)

On/Off status

Alarm number

You can set five independent Daily Alarms. When an alarm is turned on, the alarm tone sounds when the alarm time is reached.

You can turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.

•There are six screens in the Alarm Mode. Five are for

alarms (indicated by numbers from

through

by

), and one is for the Hourly Time Signal (indicated

).

 

•All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.

•You can select any one of three alarm beeper patterns.

Start

Split

 

Split release

Stop

Clear

 

(

displayed)

 

 

 

Two Finishes

 

 

 

 

 

Start

Split

 

Stop

Split release

Clear

 

First runner

Second runner

Display time of

 

 

finishes.

finishes.

second runner.

 

 

Display time of

 

 

 

 

first runner.

 

 

 

Countdown Timer

You can set the countdown timer within a range of

Minutes one minute to 24 hours. An alarm sounds when the countdown reaches zero.

To set an alarm time

1.In the Alarm Mode, use Dto scroll through the alarm screens until the one whose time you want to set is

displayed.

•To set an alarm, display one of the screens indicated by an alarm number from

through .

2.After you select an alarm, hold down A until the hour setting of the alarm time starts to flash, which indicates the setting screen.

•This operation turns on the alarm automatically.

3.Press Cto move the flashing between the hour and minute settings.

4.While a setting is flashing, use D(+) and B(–) to change it.

•When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator).

5.Press A to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds, regardless of the mode the watch is in.

•To stop the alarm tone after it starts to sound, press any button.

To test the alarm

In the Alarm Mode, hold down Dto sound the alarm.

•The alarm will sound using the currently selected beeper pattern.

To turn an alarm on and off

1. In the Alarm Mode, use Dto select an alarm.

Alarm on indicator

2. Press Ato toggle it on (

displayed) and off

 

 

(

displayed).

 

 

 

 

• Turning on an alarm (

through

) displays the

 

 

alarm on indicator on its Alarm Mode screen.

• In all modes besides the Alarm Mode, the alarm on indicator is shown for any alarm that is currently turned on.

•The alarm on indicator flashes while the alarm is sounding.

On/Off status

• You can also select auto-repeat, which automatically restarts the countdown from the original value you set whenever zero is reached.

•All of the operations is this section are performed in the

Countdown Timer Mode, which you can enter using C.

Hours Seconds

To use the countdown timer

Press Dwhile in the Countdown Timer Mode to start the countdown timer.

•When the end of the countdown is reached and auto-repeat is turned off, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is automatically reset to its starting value after the alarm stops.

•When auto-repeat is turned on, the countdown will restart automatically without pausing when it reaches zero. The alarm sounds to signal when the countdown reaches zero.

•The countdown timer measurement operation continues even if you exit the Countdown Timer Mode.

•Press Dwhile a countdown operation is in progress to pause it. Press Dagain to resume the countdown.

•To completely stop a countdown operation, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value.

To set up the countdown timer

1. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the hour setting of the countdown start time starts to flash, which indicates the setting screen.

•If the countdown start time is not displayed, use the procedure under “To use the countdown timer” to display it.

2.Press C to move the flashing in the sequence shown below to select other settings.

Hours Minutes Auto-repeat

3.While a setting is flashing, use D and B to change it as described below.

Screen

To do this:

 

 

 

 

 

Do this:

 

Change the hours or minutes

 

Use D(+) and B(–).

 

Toggle auto-repeat on (

 

) and off (

 

)

 

Press D.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• To specify a countdown start time of 24 hours, set

.

 

4. Press Ato exit the setting screen.

•The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode screen while this function is turned on.

•Frequent use of auto-repeat and the alarm can run down battery power.

2