Operation Guide 3085
Edit Mode
You can use the Edit Mode to configure various settings, such as the main display style and the alarm beeper pattern.
The following are the settings that you can configure in the Edit Mode.
•Button operation tone on/off
•Alarm beeper pattern
•
•Main display area style
•
•All of the operations in this section are performed in the Edit Mode, which you enter by pressing C.
•Each press of the D button cycles through available settings in the sequence shown below.
| Press . |
|
|
|
|
| |||||
Button Operation |
|
|
|
| Alarm Beeper |
|
|
|
| ||
Tone ( | ) |
|
|
| Pattern ( | ) |
|
| Timekeeping ( | ) | |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Main Display |
| |||
( | ) |
|
|
|
|
|
|
|
| Area Style ( | ) |
Button Operation Tone
The button operation tone sounds any time you press one of the watch’s buttons. You can turn the button operation tone on or off as desired.
•Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and Countdown Timer Mode alarm all operate normally.
To turn the button operation tone on and off
1.In the Edit Mode, use Dto display the Button Operation Tone selection screen.
2. Press Ato toggle the button operation tone on ( | ) | |
and off ( | ). |
|
On/Off status
Alarm Beeper Pattern
You can select any one of three alarm beeper patterns.
•To hear what the current beeper sounds like, see “To test the alarm”.
To change the alarm beeper pattern
1. In the Edit Mode, use D to display the Alarm Beeper Pattern selection screen.
2. Use Ato change the setting.
12/24-hour Timekeeping
You can select either
To select 12-hour or 24-hour timekeeping
1.In the Edit Mode, use Dto display the
2. Press Ato toggle between | ) and 24- | |
hour ( | ) timekeeping. |
|
•With the
•With the
•The
Main Display Area Style
You can select from among five different styles for the main display area.
•: Background/figure color combination same as the upper and lower display areas (Regular)
•: Background/figure color combination opposite
that of the upper and lower display areas (Reverse)
•: Switches between Regular and Reverse automatically every 30 seconds (00 and 30).*
•: Switches between Regular and Reverse automatically every 30 minutes (00 and 30).*
•: Switches between Regular and Reverse automatically every 12 hours (6:00 a.m. and 6:00 p.m.)*
*When any of these switching operations is selected, the main display area style is Regular while a setting screen or the Edit Mode screen is on the display.
To select the main display area style
1.In the Edit Mode, use Dto display the Main Display Area Style selection screen.
2.Use Ato change the setting.
00-second Animation
You can use this setting to turn display animation on or off. The display animation is blink animation that is played each time the seconds reach 00 in the Timekeeping Mode (except when a setting screen is on the display) and World Time Mode.
To turn 00-second animation on and off
1.In the Edit Mode, use Dto display the
2. Press A to toggle | ) and | |
off ( | ). |
|
On/Off status
To reset all Edit Mode settings to their initial defaults
In the Edit Mode, hold down Band Dfor about three seconds until flashes on the display and the watch beeps.
•This returns all Edit Mode settings to their initial default settings.
Button Operation Tone
Alarm Beeper Pattern
Main Display Area Style
Illumination
Two LEDs
turns on illumination automatically when you angle the watch towards your face for reading.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” for more important information.
To illuminate the display
In any mode (except when a setting screen is on the display), press B to turn on illumination.
•The above operation turns on illumination regardless of the current auto light switch setting.
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it towards you at more than 40 degrees causes illumination to turn on.
•Wear the watch on the outside of your wrist.
Parallel to ground | More than 40 ° |
|
Warning!
•Always make sure you are in a safe place whenever you are reading the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not startle or distract others around you.
•When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down Bfor about three seconds to toggle the auto light switch on (auto light switch indicator displayed) or off (auto light switch indicator not displayed).
•The auto light switch indicator is on the display in all modes while the auto light switch is turned on.
•In order to protect against running down the battery, the auto light switch turns off automatically approximately six hours after you turn it on.
Auto Zoom
In any mode besides the Edit Mode (and except while any setting screen is displayed and while an icon is displayed immediately after entering a mode), angling the watch towards your face for viewing will cause the figures in the main display area to enlarge automatically.
•The figures will return to normal size after about two seconds or if you perform any button operation.
•For more information about the arm position that triggers Auto Zoom, see “About the Auto Light Switch”.
Angle the watch towards your face...
3