Operation Guide 3334
Using Alarms and the Hourly Time Signal
4. Press the C button.
• This moves the flashing to |
the minute digits. As with |
(Back)
Turning an Alarm or the Hourly Time Signal On and Off
You can set up to five independent daily alarms. An alarm sounds for 10 seconds when an alarm time is reached.
The Hourly Time Signal causes the watch to beep every hour on the hour.
Setting an Alarm Time
2. Hold down A for about one second until the hour digits of the alarm time start to flash.
• | This is the setting screen. |
• | This also causes the alarm |
| indicator to appear in the top |
Alarm Indicator
the hour setting, use the D |
(+) and B |
change the minute setting. |
(Forward)
Minutes
1. In the Alarm Mode, use the D button to select the alarm (A1 to A5) or the Hourly Time Signal.
2. Press the B button to toggle the currently displayed alarm or the Hourly Time Signal on and off.
1. In the Alarm Mode, use the
D button to scroll through the alarm numbers in the left dial (A1 to A5) until the one you want is displayed.
•The current alarm time setting for the selected alarm will appear in the bottom dial.
–
Alarm1 | Alarm2 |
(AL1) | (AL2) |
Hourly Time | Alarm5 |
Signal(SIG) | (AL5) |
Alarm Number Graph
(Forward)
Alarm Time
Alarm
Number
Alarm3
(AL3)
Alarm4
(AL4)
| dial, and automatically turns |
| on the alarm. |
3. | Use the D (+) and B |
| buttons to change the |
| hour setting. |
• | Holding down either button |
| scrolls the hour setting at high |
| speed. |
• | When setting the hour, make |
| sure you specify AM (no |
| indicator) or PM (P) correctly |
| when using |
| timekeeping, or that you |
| specify the correct |
| time. |
• | The same |
| format you select for the |
| Timekeeping Mode time is |
| also applied in the Alarm |
| Mode. |
Hour
(Back)
(Forward)
5. After all of the setting is the way you want, press the A button.
•This exits the setting screen.
•The watch will also exit the setting screen automatically if you do not perform any operation for about two or three minutes.
• | Turning on an alarm or the Hourly Time Signal causes its |
| indicator to appear in the top dial. |
• | Turning on an alarm also causes its alarm time setting to |
| appear in the bottom dial. |
Alarm Indicator | Hourly Time Signal Indicator |
Alarm 2 Screen | Timekeeping Screen |
Stopping the Alarm Beeper
Pressing any button while an alarm is sounding stops it.
Testing the Alarm
In the Alarm Mode, hold down the B button to sound the alarm tone.
Using the Timer
4. Use the D and B buttons to select the type of timer you want to use.
Using the Timer
In the Timer Mode, press the D button.
You can set the start time of the time in the range of 1 to 60 minutes, in units of one minute. The watch beeps for 10 seconds when the end of the countdown is reached. Turning on the auto repeat feature causes the countdown to restart from the start time whenever the end of the countdown is reached.
Timer Types
There are two different settings that you can use to configure the timer as describe below.
•Repeat
With Repeat, the countdown stops, the original start time appears, and the watch beeps for 10 seconds when the end of the countdown is reached.
•Auto Repeat
Auto Repeat causes timing to restart from the start time when the end of the countdown is reached.
•The countdown repeats up to 10 times, or until you stop it manually.
Configuring Timer Settings
1. In the Timer Mode, hold down A for about one second until the minute digits of the timer start time start to flash in the bottom dial. This is the setting screen.
Minutes
2. Use the D (+) and B
• Holding down either button scrolls the start time setting at high speed.
(Back)
(Forward)
•To select Repeat, display “
”.
• To select Auto Repeat, display “ | ”. Selecting Auto Repeat |
also displays a value in the left dial indicating the current | |
number of repeats. |
|
Repeat | Auto Repeat |
or 
Number of Repeats
5. After the settings are configured the way you want, press the A button.
•This exits the setting screen.
•The watch will also exit the setting screen automatically if you do not perform any operation for about two or three minutes.
•Each press of the D button starts or stops the countdown.
•Repeat counts down in
Repeat | Auto Repeat |
1/10 | Number of |
second | (Reset) Repeats |
(Start/Stop) | |
Minutes Seconds | Minutes Seconds |
•Pressing the B button while the countdown is stopped resets the display time to the start time.
•Pressing the D button again while the timer countdown is stopped restarts the countdown.
3. Press the C button to change to the timer type setting.
End of Countdown
The watch beeps for 10 seconds when the end of the countdown is reached.
•Pressing any button while the beeper is sounding stops it.
6