Casio MA0905-EB, SGW200-1V, SGW2001V manual

MA0905-EB

Operation Guide 3166

Getting Acquainted

Thank you for purchasing this CASIO product. To ensure that it can provide you with the years of service for which it is designed, be sure to read this manual carefully and follow the instructions contained herein.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered by you or any third party arising through the use of this product or its malfunction.

Low Battery Warning

If you use the light or alarms a number of times during a short period, a R (recover) indicator will ﬂash on the display and the following operations become disabled as the battery level recovers.

• Pedometer functions

• Alarm and hourly time signal

• Illumination

Normal operation should return after the battery level recovers, but if the R indicator appears frequently you should have the watch’s battery replaced.

��

About This Manual

•Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the information you need to perform operations in each mode.

General Guide

•Use Cto navigate between modes.

•Holding down Cfor about three seconds in any mode will return to the Timekeeping Mode.

•Pressing Lin any mode will illuminate the display.

��

Setting the Time and Date

��

Use the following procedure to set the current time and

date after having the watch’s battery replaced, etc. World

��

Time Mode times will not be displayed correctly unless

you conﬁgure your Home Time settings (the time in the

city where you normally will use the watch) correctly.

• If you to use the watch in Japan, select TYO (Tokyo) as

your Home Time.

To set the time and date

1. In the Timekeeping Mode, hold down Afor about two

seconds until the seconds digits start to ﬂash. This is

the setting screen.

��

2.Use Cto move the ﬂashing to the time, date, or Home City setting as shown

above, and then use D(+) and B(−) to change the ﬂashing setting.

• Holding down Dor Bwill change the selected setting at high speed.

Setting	To do this:	Do this:
Seconds	Reset to 00	Press D.
Summer Time (DST)	Toggle between standard time (OFF) and	Press D.
	daylight saving time (ON)
Home City	Change the Home City setting (See the	Use D(east) and
Home City	“City Code Table”.)	B(west).
	“City Code Table”.)	B(west).
Hour, Minute	Change the hour or minute setting	Use D(+) and B(–).
12/24-hour Timekeeping	Toggle between 12-hour and 24-hour	Press D.
12/24-hour Timekeeping	timekeeping	Press D.
Year, Month, Day	Change the year, month, or day setting	Use D(+) and B(–).

3.After all of the settings are the way you want, press Atwice to exit the setting screen.

•The watch also will exit the setting screen automatically if you do not perform any operation for about two or three minutes.

•When setting the hour, make sure you specify AM (no indicator) or PM (P) correctly, or that you specify the correct 24-hour time.

•Resetting the seconds to 00 while the current count is in the range of 30 to 59 causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are reset to 00 without changing the minutes.

•Resetting the zero count to zero on an accurate time signal about once a month helps to ensure accurate timekeeping.

•You can set a date in the range of January 1, 2000 to December 31, 2099.

•The day of the week is set automatically in accordance with the date you set.

•The watch makes adjustments for leap years and month lengths automatically.

•Summer time, or Daylight Saving Time (DST) as is it is called in some countries, calls for setting clocks ahead one hour during the summer season. Note that the use of summer time depends on the country and even the local area.

Stopwatch

The Stopwatch Mode lets you measure elapsed time, and record lap/split times. A sensor built into the watch counts your steps while a stopwatch elapsed time operation is in progress. The watch uses this information to calculate the energy you consume, the distance you cover, and your average pace in accordance with personal information you pre-register.

For each elapsed time operation, the watch creates a record in memory to record the date, lap/split times, distance covered, energy consumption, number of steps, and other information.

Stopwatch

•Minimum Measuring Unit: 1/100 second

•Maximum Measuring Time: 99:59'59.99''

•Lap/Split Count: 999

Elapsed Time Measurement

•Workout Time

•Distance Covered

•Energy Consumption

•Average Pace (*)

•Number of Steps

Workout Data (Maximum Cumulative Values)

•Laps/splits: 150

•Cumulative Distance: 999.9 km/621.1 miles

•Cumulative Energy Consumption: 23900.5kcal / 99999.9kJ

•Average Pace: 220 (*)

•Cumulative Number of Steps: 999999

•Cumulative Exercise Time: 9999 hours, 59 minutes

•Best Lap

*Average Pace

•The average pace value shows your average number of steps per minute while timing your run with the stopwatch.

•When you take a lap reading, this value shows your average pace during that lap.

•When you take a split reading, this value shows your average pace up to the current split, starting from the start of your timed run.

Getting Acquainted

Low Battery Warning

About This Manual

General Guide

Setting the Time and Date

To set the time and date

Setting

To do this:

Do this:

Stopwatch

Stopwatch

Elapsed Time Measurement

Workout Data (Maximum Cumulative Values)