CAUTION: DISCONNECT POWER BEFORE ATTEMPTING ANY ELECTRICAL REPAIRS

THERMOSTAT ADJUSTMENTS:

NOTE: The thermostat is behind the lower front panel. If water temperature is less than 197 degrees F

(92 degrees C) slowly turn thermostat knob clockwise until ready light goes out. When temperature of water approaches 197 degrees to 203 degrees F (92 degrees to 95 degrees C) slowly turn thermostat knob counter- clockwise until the green ready light comes on. If water temperature cannot be increased when thermostat knob is turned fully clockwise, then proceed as follows:

Pull off knob. Place a small screwdriver into the center of thermostat shaft. While observing green ready light and temperature on thermometer, hold shaft and turn small adjustment screw in center counter-clockwise until green ready light goes out.When temperature of water approaches 197 degrees - 203 degrees F (92 degrees - 95 degrees C), slowly turn screw clockwise until ready light comes on. Turning screw clockwise lowers temperature; counter-clockwise raises it. After adjusting center screw, place nail polish or glyptol on screw to set in position.

NOTE: As a final check, measure water temperature at Spray Head . Temperature should be 197 degrees to 203 degrees F (92 degrees to 95 degrees C).

PROBLEMS WITH WARMER ELEMENTS & SWITCHES:

If warmer plate fails to heat, first check power source and then check if light on warmer switch is lit when in the “ON” position. If warmer switch is lit, replace warmer plate by unplugging brewer, removing the two hold down screws on plate and withdrawing warmer plate from brewer. Replace the new warmer plate. If warmer switch does not light, replace it. To remove switch press each tab behind front plate of brewer down with screwdriver in turn. As each tab is pressed, pop that corner of warmer switch out of the front of brewer. New switch snaps in from the front.

IF WATER FAILS TO HEAT:

1.If Red power switch and warmer switches do not light, check heater switch in the back, toggle should be in the up position . Check power supply outlet, replace fuse or reset circuit breaker if necessary. If power is good, check rear heater switch for continuity and replace if switch stays open.

2.If water still fails to heat, disconnect line cord and check out tank heater, thermostat and high temperature safety shutoff. Replace needed parts.

REPLACING HI-LIMIT SWITCH, THERMOSTAT, AND TANK HEATER

Unplug power cord, and remove top cover and lower front cover.

HI-LIMIT SWITCH Disconnect the (2) push-on leads, and pull out hi-limit. Replace switch

THERMOSTAT Loosen (2) screws securing thermostat to housing. Disconnect the push-on leads and remove thermostat. Replace with new one in reverse order. When installing new control, do not overtighten small packing nut on compression fitting.

TANK HEATER Remove tank top, (4) hex nuts and washers. Disconnect push-on leads. Replace in reverse order. Remove the lower panel and loosen the (2) screws holding thermostat in place.Slide thermostat out of bracket and remove wires. Remove top cover and pull out Capillary Tank fitting from silicone grommet.

Man-page11-14.doc

14

Page 14 Page 16
Page 15
Image 15
Cecilware 2000 manual Thermostat Adjustments
Page 14 Page 16

2000 specifications

The Cecilware 2000 is a remarkable coffee and espresso machine that delivers exceptional performance and durability, making it a popular choice for both commercial establishments and coffee enthusiasts. Designed for high-volume environments, this sophisticated machine combines innovative technology with user-friendly features to consistently produce high-quality beverages.

One of the standout features of the Cecilware 2000 is its powerful brewing system. It is equipped with dual boiling systems that ensure precise temperature control for optimal extraction of flavors from coffee grounds. The machine can handle multiple orders simultaneously, which is essential for busy cafés and restaurants. This capacity for high output allows baristas to cater to large crowds, maintaining efficiency during peak hours.

Another notable aspect of the Cecilware 2000 is its intuitive control panel. The user-friendly interface includes programmable options for brewing strength, cup sizes, and auto-timer settings, allowing baristas to customize each beverage to their customers' preferences easily. This versatility not only improves the speed and consistency of drink preparation but also enhances the overall customer experience.

In terms of build quality, the Cecilware 2000 is constructed from durable materials to withstand the rigors of daily use. Its robust design ensures longevity, making it a worthwhile investment for any coffee business. The machine also features a compact footprint, allowing it to fit in various kitchen layouts without taking up excessive space.

The integration of advanced technologies in the Cecilware 2000 further elevates its capabilities. It employs a PID (Proportional Integral Derivative) control system, which maintains optimal brewing temperatures, ensuring that every cup of coffee or espresso is brewed to perfection. Additionally, the machine showcases energy-efficient components that reduce power consumption, making it environmentally friendly and cost-effective.

Moreover, the Cecilware 2000 offers impressive milk frothing capabilities. Its steam wand is designed for easy maneuverability, enabling baristas to create frothy textures for lattes and cappuccinos with precision. This feature is essential for producing specialty drinks that appeal to a wide range of customers.

In summary, the Cecilware 2000 stands out as a top-tier coffee and espresso machine, thanks to its combination of advanced technology, user-friendly features, and robust construction. Ideal for high-traffic environments, it provides versatility and efficiency while ensuring the consistent production of high-quality beverages. Whether for a busy café or an upscale restaurant, the Cecilware 2000 remains a reliable choice for those seeking excellence in coffee brewing.
Top Page Image Contents