LOCKOUT POSITION (MANUAL DISCONNECT)
NOTICE
Open
Close Stop

Using the Wall-Mounted

 

 

Door Control

 

 

THE MULTI-FUNCTION DOOR CONTROL

 

Press the push bar to open or close

 

Push

the door. Press again to reverse the

 

 

Button

door during the closing cycle or to

 

Lock

stop the door while itís opening.

 

 

Button

Light feature

LIGHT

Light

 

LOCK

 

Button

Press the Light button to turn the

opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for

4-1/2 minutes. Press again to turn it off sooner. The

4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold the Lock button until the light blinks (about 10 seconds). A single blink indicates that the timer is reset to 1-1/2 minutes. Repeat the procedure and the light will blink twice, resetting the timer to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 minutes.

Lock feature

Designed to prevent operation of the door from hand-held remote controls. However, the door will open and close from the Door Control, the Outside Keylock and the Keyless Entry Accessories.

To activate, press and hold the Lock button for 2 seconds. The push bar light will flash as long as the Lock feature is on.

To turn off, press and hold the Lock button again for 2 seconds.The push bar light will stop flashing. The Lock feature will also turn off whenever the ìLearnî button on the motor unit panel is activated.

B)To operate one door using all three buttons on the hand-held remote:

You may program the remote to open the door with the large button, close it with the middle button, and stop the doorís movement with the third button.

NOTE: If remote is already programmed, you must first erase all codes. See Programming.

1.With the door closed, press and hold the large remote push button.

2.Press and hold the Lock button on the door control.

3.Press and hold the door control push bar.

4.After the opener lights flash, release all buttons.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

•If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

•NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

•NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.

To Open the Door Manually

Additional features when used with the 3-Button hand-held remote

A) To control the opener lights:

In addition to operating the door, you may program the remote to operate the lights.

1. With the door closed, press and hold a

small remote button that you want to

DISCONNECT TROLLEY:

The door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually.

Trolley

Trolley

Release Arm

(in Manual

Disconnect

Position)

control the light.

2. Press and hold the Light button on the

Multi-Function door control.

3. While holding the Light button, press and hold the

Lock button on the door control.

4. After the opener lights flash, release all buttons.

The lockout feature prevents the trolley from reconnecting automatically, and the door can be raised and lowered manually as often as necessary.

TO RE-CONNECT THE TROLLEY:

Pull the emergency release handle toward the opener at a 45° degree angle so that the trolley release arm is horizontal. The trolley will reconnect on the next UP or DOWN operation, either manually or by using the door control or remote.

 

Trolley

 

Trolley

Emergency

Release

Arm

Release

 

Handle

NOTICE

(Pull at 45° angle)

TO RECONNECT

27