Using the Wall-Mounted Door Control

THE MOTION DETECTING DOOR CONTROL

2. Press and hold the Light button on the door control.

3. While holding the Light button, press and hold the

Lock button on the door control.

4. After the opener lights flash, release all buttons.

Press the push bar to open or close the door. Press again to reverse the door during the closing cycle or to

Push

Bar

B)To operate one door using all three buttons on the hand-held remote:

stop the door while it's opening.

This door control contains a motion detector that will automatically turn on the light when it detects a person entering the garage. This feature can be easily turned off for extended work light use.

Detector

Switch

LOCK

LIGHT

Lock

Button Light

Button

You may program the remote to open the door with the large button, close it with the middle button, and stop the doorís movement with the third button.

NOTE: If remote is already programmed, you must first erase all codes. See Programming.

Open

Close

Stop

Light feature

Press the Light button to turn the opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for 4-1/2 minutes. Press again to turn it off sooner. The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold the Lock button until the light blinks (about 10 seconds). A single blink indicates that the timer is reset to 1-1/2 minutes. Repeat the procedure and the light will blink twice, resetting the timer to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 minutes.

When using the opener lights as working lights, we recommend that you first disable the motion sensor See Automatic Light Feature, following.

Automatic Light Feature: The opener light will turn on automatically when a person enters the garage. When a person walks in front of the door control, the light will come on for five minutes, then shut off. This feature works by detecting body heat and may not work in temperatures around 100˚F (37.7˚C).

To disable this feature, slide the Detector Switch on the right side of the door control down (off).

1.With the door closed, press and hold the large remote push button.

2.Press and hold the Lock button on the door control for a minimum of one second before proceeding to next step.

3.Press and hold the door control push bar.

4.After the opener lights flash, release all buttons.

To Open the Door Manually

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

•If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

•NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

•NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.

We recommend that you disable the motion sensor when using the opener lights as working lights. Otherwise, they will turn off automatically if you are working beyond the sensorís range.

Lock feature

Designed to prevent operation of the door from hand-held remote controls. However, the door will open and close from the Door Control, the Outside Keylock and the Keyless Entry Accessories.

To activate, press and hold the Lock button for 2 seconds. The push bar light will flash as long as the Lock feature is on.

To turn off, press and hold the Lock button again for 2 seconds.The push bar light will stop flashing. The Lock feature will also turn off whenever the ìLearnî button on the motor unit panel is activated.

Additional features when used with the 3-Button hand-held remote

A) To control the opener lights:

In addition to operating the door, you may program the remote to operate the lights.

1.With the door closed, press and hold a small remote button that you want to control the light.

The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually. To reconnect the door to the opener, press the door control push bar.

The lockout feature prevents the trolley from reconnecting automatically, Pull the emergency release handle down and back (toward the opener). The door can then be raised and lowered manually as often as necessary. To disengage the lockout feature, pull the handle straight down. The trolley will reconnect on the next UP or DOWN operation.

 

Trolley

Emergency

Release

Arm

Release

 

Handle

N

 

(Pull Down)

OT

ICE

 

MANUAL DISCONNECT

POSITION

Trolley

Release

Arm

Emergency

Release Handle

(Down and Back)

TICE

NO

LOCKOUT POSITION

28