Manuals / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 3453135556 manual Series OCG, 1.800.929.3667, For Answers and Assistance

Models: 3453135556

1 28

Download 28 pages 4.78 Kb

Page 1

Image 1

3453135556

Series OCG

Includes Remote Control and SERIES II Electronics

Included Wall Control MUST be installed prior to operation of this Garage Door Operator

Safe-T-Beam®Safety Reverse System Must be installed to close door

NOTE: Your Operator comes with a Rail Assembly which is standard for up to a 7 foot 6 inch high door. An extension kit for an 8 foot high door is available.

For Answers and Assistance:

1.800.929.3667

or visit www.overheaddoor.com

SAVE THIS MANUAL FOR FUTURE REFERENCE

Page 1

Image 1

Chamberlain 3453135556 manual Series OCG, 1.800.929.3667, Includes Remote Control and SERIES II Electronics

Contents

Safe-T-Beam Safety Reverse System Must be installed to close door Includes Remote Control and SERIES II ElectronicsSeries OCG 1.800.929.3667Things to consider if you are planning to “do-it-yourself.” TYPICAL 1-PIECE DOOR INSTALLATION TYPICAL SECTIONAL DOOR INSTALLATION48 POWER CORD TO 120V GROUNDED OUTLET EXTENSION SPRING OR TYPICAL SUPPORT BRACKETOPERATOR FEATURES TABLE OF CONTENTSSAFETY FEATURES Operator MUST be installed with the included Wall ControlPARTS IDENTIFICATION - Not Shown Full Size TOOLS RECOMMENDEDFASTENERS - Shown Full Size . See Parts List for description 1-PIECE BOOM HARDWARE EXPLODED VIEW PARTS LISTFOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM Part NamePOWER HEAD POWER HEAD EXPLODED VIEWSAFETY INFORMATION PARTS LIST pre-assembledOPEN BLUE PARTS BAG OPERATOR ASSEMBLYBoom is up-side down BOOM ASSEMBLY Use a clean, flat surface3. Attach boom to power head OPEN GREEN PARTS BAGAttach to hole in emergency release using metal FIG. 1-4 Attach boom to power head7. Attach limit switch wires 6. Attach limit switchesBundle HEADER AND DOOR MOUNTING BRACKETS INSTALLATIONTo reduce the risk of severe injury or death I M P O R TA N TDOOR BRACKET OPEN ORANGE PARTS BAG2. Mounting the header bracket 3. Finding door bracket mounting locationMOUNTING THE OPERATOR 4647ANGLE IRON ON FINISHED CEILING UNFINISHED OR OPEN BEAMINSTALL DOOR ARMS 1-piece doors INSTALL DOOR ARMS Sectional doors2728 OPEN YELLOW PARTS BAG3. Wiring 3 SAFE-T-BEAM SYSTEM INSTALLATION1. Mounting brackets 2. Mounting “STB” source and sensor3. Wiring cont’ OPEN RED PARTS BAG4. Check the following 2. Wiring 4 WALL CONTROL INSTALLATION1. Finding the mounting location 3. MountingSafe-T-Beam Alignment Check WITH PERMANENT WIRING5 CONNECTING TO POWER WITH GROUNDED PLUG 1. Plug the operator into a properly grounded electrical outlet1. Adjusting limit switches 6 LIMIT SWITCH / FORCE ADJUSTMENT2. Adjusting “OPEN” force 3. Adjusting “CLOSE” forceFCC and IC CERTIFIED 7 PROGRAMMING REMOTE CONTROLS SINGLE BUTTON REMOTECONTACT REVERSE TEST The force adjustments and limit switch9 LIGHT BULB/LENS INSTALLATION 8 REMOTE CONTROLMULTI-BUTTON REMOTE LOST OR STOLEN REMOTETROUBLESHOOTING GUIDE 10 MAINTENANCE ROUTINE MONTHLY MAINTENANCEIMPORTANT SAFETY INSTRUCTIONS Toreduce the risk of severe injury or deathRemote control TROUBLESHOOTING GUIDE CONTINUEDRelocate remote control inside car Point remote control at garage doorFOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM WIRING DIAGRAMTRANSMITTER COMPLIANCE STATEMENT INSTALLATION NOTESFOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM Limited Warranty BE AVAILABLE IF YOU EVER NEED TO CALL USSerial Number Operator Model Remote Control Model Dealer Name LOCATED UNDER LENS OF POWER HEADCall Access Systems Division 22790 Lake Park Blvd Alliance, OhioOverHead Door Corporation Call Access Systems Division 22790 Lake Park Blvd Alliance, OhioOverHead Door Corporation