Chamberlain 3585 3/4 Carton Inventory, INSTALLATION HARDWARE

Carton Inventory

Your garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below. Accessories will depend on the model purchased.

If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below.

Belt Cap Retainer

LOCK LIGHT

Remote Controll TransmitterVisor Clip Visor Clip

Smart Control PanelTM	SECURITY✚®	Styrofoam
LCD Motion Detecting	3-Button Remote Control
Door Control Console	Model 373P (1)
		Belt

Motor Unit w/Light Lenses

One-Piece

Rail

2-Conductor Bell Wire

White & White/Red

	NLY
	T O
	UN
NG	MO
NG
ILI
CE
	UP

Trolley

Header Bracket

Belt

Pulley Bracket

Door Bracket

Curved Door Arm Section

	The Protector System®
	(2) Safety Reversing Sensors
	(1 Sending Eye and 1 Receiving Eye)
	with 2-Conductor White & White/Black
Safety Sensor	Bell Wire attached
Bracket (2)

Safety Labels and Literature

Straight Door Arm Section

INSTALLATION HARDWARE
Hex Bolt 5/16"-18x7/8" (4)	Self-Threading Screw 1/4"-14x5/8" (2)
Hex Screw #8 x 3/8" (2)	Screw 6-32x1" (2)
Lag Screw 5/16"-9x1-5/8" (2)	Insulated Staples (30)
Lag Screw 5/16"-18x1-7/8" (2)	Ring Fastener (3)
Clevis Pin 5/16"x2-3/4" (1)	Drywall Anchors (2)
Clevis Pin 5/16"x1-1/4" (1)	Rope
Clevis Pin 5/16"x1" (1)	Handle
Nut 5/16"-18 (4)	Rail Grease
Lock Washer 5/16" (4)	Carriage Bolt 1/4"-20x1/2" (2)
Screw 6ABx1-1/4" (2)	Wing Nut 1/4”-20 (2)

5

Contents

For Residential Use Only Introduction2-5 Assembly Installation7-22 Adjustment23-25 Operation26-31 Preparing your garage door Tools needed Planning Carton Inventory Attach the Rail to the Motor Unit Set the Belt Tension Attach the Belt Cap Retainer Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING ALIGNING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1. Assemble the door arm, Figure 4: 2. Adjustment procedures, Figure 5: • Open door adjustment: decrease UP travel limit 3. Connect the door arm to the trolley: Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control Using the Remote Control The Remote Control Battery Troubleshooting To Open the Door Manually HAVING A PROBLEM My door will not close and the light bulbs blink on my motor unit: 2.My remotes will not activate the door: My door reverses for no apparent reason: 5.My lights will not turn off when door is open: 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES Smart Control Panel™ Messages Message To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 1702LM Outside Quick Release: 41A5281 Extension Brackets: 377LM Page Page LIFTMASTER® GARAGE DOOR OPENER FIVE-YEARLIMITED WARRANTY LIFETIME MOTOR AND BELT LIMITED WARRANTY