Chamberlain 3595CS Hang the Opener

	INSTALLATION STEP 5

	Hang the Opener
			To avoid possible SERIOUS INJURY from a falling garage door

	Three representative installations are shown. Yours may		opener, fasten it SECURELY to structural supports of the
			garage. Concrete anchors MUST be used if installing any
	be different. Hanging brackets should be angled (Figure 1)
			brackets into masonry.
	to provide rigid support. On finished ceilings (Figure 2 and

	Figure 3), attach a sturdy metal bracket to structural

	supports before installing the opener. This bracket and
	fastening hardware are not provided.		Figure 1

Structural

1. Measure the distance from each side of the motor unitSupports to the structural support.

	2. Cut both pieces of the hanging bracket to required	Measure	Lag Screws
	lengths.		5/16"-18x1-7/8"
		Distance

3. Drill 3/16" pilot holes in the structural supports.

4. Attach one end of each bracket to a support with 5/16"-18x1-7/8" lag screws.

5. Fasten the opener to the hanging brackets with			Bolt 5/16"-18x7/8"
5/16"-18x7/8" hex bolts, lock washers and nuts.			Lock Washer 5/16"
6. Check to make sure the rail is centered over the door			Nut 5/16"-18
6. Check to make sure the rail is centered over the door
(or in line with the header bracket if the bracket is not
centered above the door).
7. Remove the 2x4. Operate the door manually. If the			Figure 2
door hits the rail, raise the header bracket.			Figure 2	Hidden
8. Grease the top and underside of the rail surface				Support
8. Grease the top and underside of the rail surface			Bracket	FINISHED CEILING
where the trolley slides with rail grease.			(Not Provided)	FINISHED CEILING
NOTE: DO NOT connect power to opener at this time.				Lag Screws
				5/16"-18x1-7/8"
				(Not Provided)
				Bolt 5/16"-18x7/8"
				Lock Washer 5/16"
				Nut 5/16"-18
HARDWARE SHOWN ACTUAL SIZE
			Bolt 5/16"-18x7/8"
Lag Screw 5/16"-18x1-7/8"			Lock Washer 5/16"
			Nut 5/16"-18
Hex Bolt		Lock Washer 5/16"	Figure 3
5/16"-18x7/8"	Nut 5/16"-18	Lock Washer 5/16"	Figure 3
			Lag Screws
			5/16"-18x1-7/8"	FINISHED CEILING
				(Not Provided)
				Bolt 5/16"-18x7/8"
				Lock Washer 5/16"
				Nut 5/16"-18

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

11

Contents

GARAGE DOOR OPENER Model 3595CS 3/4 HP Owner’s Manual TABLE OF CONTENTS Introduction2-5 Assembly6-7 Installation7-19 Operation23-28 Preparing your garage door Complete the following test Sectional Door Tools needed Planning SECTIONAL DOOR INSTALLATION Carton Inventory INSTALLATION HARDWARE ASSEMBLY STEP Attach the Rail to the Motor Unit Attach the Chain Spreader NOTE: Attach the Chassis Support Bracket IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk of SEVERE INJURY or DEATH: INSTALLATION STEP Determine the Header Bracket Location SECTIONAL DOOR ONLY Sectional door with curved track Install the Header Bracket WALL HEADER BRACKET INSTALLATION CEILING HEADER BRACKET INSTALLATION Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control CAUTION: SPECIAL NOTE: plastic housing. Do NOT overtighten 3. (For standard installations ONLY) Run bell wire up Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements To avoid installation difficulties, do not run the opener at this time The opener must be grounded Install The Protector System® IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR Facing the door from inside the garage INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation: Floor installation: MOUNTING AND WIRING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel Connect Door Arm to Trolley SECTIONAL DOORS ONLY Figure 1: Figure 2: Figure 3, Hole alignment alternative: ADJUSTMENT STEP Adjust the UP and DOWN Travel Limits Run the opener through a complete travel cycle after each adjustment HOW AND WHEN TO ADJUST THE LIMITS •If the door does not open completely but opens at least 5 feet (1.5 m): Adjust the Force HOW AND WHEN TO ADJUST THE FORCES 1. Test the DOWN (close) force If the door is hard to hold or doesn’t reverse 2.Test the UP (open) force Test the Safety Reversal System TEST must ADJUST IMPORTANT SAFETY CHECK: IMPORTANT SAFETY INSTRUCTIONS Using the Wall-MountedDoor Control THE SMART CONTROL PANEL™ (PROG) Learn Feature Hour & Minute Feature Light feature Using the Remote Control Proximity Disable Feature The Remote Control Batteries To Control the Opener Lights Troubleshooting To Open the Door Manually MAINTENANCE SCHEDULE Once a Month Twice a Year Once a Year Having a Problem? (Continued) 5.Opener noise is disturbing in living quarters of home: 6. The garage door opens and closes by itself: 7. The door doesn’t open completely: 8. The door stops but doesn’t close completely: Smart Control Panel™ Messages Message PROGRAMMING NOTICE: To Add or Reprogram a Hand-heldRemote Control USING THE “LEARN” BUTTON USING THE SMART CONTROL PANEL™ To Add, or Reprogram or Change a Keyless Entry PIN To change an existing, known PIN To set a temporary PIN hours times REPAIR PARTS Rail Assembly Parts KEY PART NO. NO. DESCRIPTION Installation Parts Motor Unit Assembly Parts ACCESSORIES 1702LMC Outside Quick Release: 41A5281 Extension Brackets: LIFTMASTER® SERVICE HOW TO ORDER IS ON CALL REPAIR PARTS LIFTMASTER® GARAGE DOOR OPENER FIVE-YEARLIMITED WARRANTY Pour résidences seulement TABLE DES MATIÈRES Introduction Montage Pose Fonctionnement23-28 Préparation de votre porte de garage Outils nécessaires Planification Inventaire de la boîte d’emballage MONTAGE – 1re OPÉRATION Fixation du rail au moteur MONTAGE – 2e OPÉRATION Fixation de l’écarteur de chaîne MONTAGE – 3e OPÉRATION IMPORTANTES INSTRUCTIONS CONCERNANT LA POSE Pour réduire le risque de BLESSURES GRAVES ou MORTELLES : POSE – 1re OPÉRATION Déterminer l’emplacement du support de linteau POSE – 2e OPÉRATION Pose du support de linteau POSE – 3e OPÉRATION Fixation du rail sur le support de linteau POSE – 4e OPÉRATION Positionnement de l’ouvre-porte POSE – 5e OPÉRATION Accrochage de l’ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE – 7e OPÉRATION Pose des l’ampoule POSE – 8e OPÉRATION Pose de la corde et de la poignée de déclenchement d’urgence POSE – 9e OPÉRATION Exigences électriques POSE – 10e OPÉRATION Pose du Système Protector® Page Page POSE – 11e OPÉRATION Fixation du support de porte POSE – 12e OPÉRATION Fixation de la biellette au chariot RÉGLAGES – 1re OPÉRATION Réglage des courses d’ouverture et de fermeture RÉGLAGES – 2e OPÉRATION Réglage de la force RÉGLAGES – 3e OPÉRATION Essai du système d’inversion de sécurité RÉGLAGES – 4e OPÉRATION Essayer le Système Protection® FONCTIONNEMENT IMPORTANTES CONSIGNES DE SÉCURITÉ ou DE MORT : Utilisation de votre ouvre-portede garage Utilisation de la commande de porte à montage mural Utilisation de la Telecommande Les Piles de Télécommande Dépannage Ouverture manuelle de la porte Défauts de fonctionnement ENTRETIEN DE L’OUVRE-PORTEDE GARAGE Défauts de fonctionnement (suite) Messages de la Smart Control Panel™ PROGRAMMATION Pour ajouter ou reprogrammer une télécommande à main supplémentaire Pour effacer tous les codes de la mémoire du moteur * Télécommandes à trois boutons Pour ajouter, reprogrammer ou modifier un NIP d’entrée sans clé PIÈCES DE RECHANGE Pièces d’assemblage du rail Pièces pour la pose Pièces d’assemblage du moteur ACCESSOIRES SERVICE LIFTMASTER® À VOTRE DISPOSITION COMMENT COMMANDER DES PIÈCES DE RECHANGE GARANTIE LIMITÉE 5 ANS SUR L’OUVRE-PORTEDE GARAGE LIFTMASTER®