Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain CG40 Rail Assembly Parts, Installation Parts, NO, NO, NO, NO, KEY, KEY, PART, PART, DESCRIPTION, DESCRIPTION, REPAIR PARTS

1 40

Download 40 pages, 1.23 Mb

REPAIR PARTS

Rail Assembly Parts
			2
1							5
1				3
				3			8
							8
6				4	KEY	PART
				4
3
3					NO.	NO.	DESCRIPTION
					1	4A1008	Master link kit
					2	41A3489	Complete trolley assembly
					3	183B112	Rail braces (each)
					4	183B111	T-rail – center sections (each)
					5	183B113	T-rail – end sections (each)
7	5				6	41A3473	Chain & cable in dispensing
7	5						carton
							carton
					7	41B2616	Cable pulley bracket assembly
					8	83A12	Rail Grease
							NOT SHOWN
						41A3534	Rail assembly hardware kit
							(see page 7).
Installation Parts
1	2			4
	2			4
3				KEY	PART
	LING M		LY	KEY	PART
		NT	ON
	OU	NT
	CEI			NO.	NO.	DESCRIPTION
	UP			NO.	NO.	DESCRIPTION
6	7			1	41A4166	Lighted door control button
6				1	41A4166	Lighted door control button
				2	41A5056-17 Single-function remote control,
5				3	10A20	housing only (no circuit board)
	9			3	10A20	3V2032 Lithium battery
	9			4	29B137	Transmitter visor clip
NOTICE				5	41A2828	Manual release rope & handle assembly
NOTICE				6	217A238	2-conductor bell wire – white & white/red
				6	217A238	2-conductor bell wire – white & white/red
		10		7	41A4353	Header bracket w/clevis pin & fastener
8		10		8	41A5047	Door bracket w/clevis pin & fastener
8				8	41A5047	Door bracket w/clevis pin & fastener
				9	178B35	Curved door arm section
	11			10	178B34	Straight door arm section
				11	12B350	Hanging brackets
12				12	41A5034	Safety sensor kit
						(receiving and sending eyes)
						with 3' 2-conductor bell wire attached
				13	41A5266-1	Safety sensor brackets (2)
13						NOT SHOWN
13					41A2848	Installation hardware bag (see page 7).
					41A2848	Installation hardware bag (see page 7).
					114A2490	Owner's manual

37

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail and Attach the Cable Pulley Bracket Install the Trolley Fasten the T-Railto the Motor Unit Install the Chain/Cable and Attach the Sprocket Cover Tighten the Chain and Cable Determine the Header Bracket Location EXAMPLE One-piecedoor without track: jamb hardware One-piecedoor without track: pivot hardware Install the Header Bracket Attach the T-Railto the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light and Lens Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation: Floor installation: MOUNTING AND WIRING THE SAFETY SENSORS ALIGNING THE SAFETY SENSORS TROUBLESHOOTING THE SAFETY SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm: 2.Adjustment procedures: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test the Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually Care of Your Opener Having a Problem Having a Problem? (Continued) To Add an Additional Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *Multi-FunctionRemotes To Add or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 953CB 956CB 945CB 935CB www.chamberlain-diy.com CHAMBERLAIN GARAGE DOOR OPENER ONE-YEARLIMITED WARRANTY