Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain HD150DM 1/3 HP, HD175DM 1/2 HP Rail Assembly Parts, Installation Parts, NO, NO, NO, NO, KEY, KEY, PART, PART, DESCRIPTION, DESCRIPTION, REPAIR PARTS

1 40

Download 40 pages, 1.26 Mb

REPAIR PARTS

Rail Assembly Parts

2

1

3

4

5

		KEY	PART
		NO.	NO.	DESCRIPTION
		1	4A1008	Master link kit
		2	41C5141-1	Complete trolley assembly
		3	41A5665-2	Complete rail
		4	144C56	Idler pulley
	6	5	41A5807	Chain and cable
	6	6	12D598-1	“U” bracket
		6	12D598-1	“U” bracket
				NOT SHOWN
			183A163	Wear pads

Installation Parts

4

1	2
	3

5	6	7
		7

NO	E
TIC

10 11

8 9

13

12


KEY		PART
NO.		NO.	DESCRIPTION
1		41A4166	Door control button
2		950D	Single-Button remote control
3		10A20	3V2032 Lithium battery
4		29B137	Remote control visor clip
5		41A2828	Emergency release rope and handle
			assembly
6		41B4494-1	2-Conductor bell wire, white and white/
			red
7		41A5047-1	Door bracket w/clevis pin & fastener
8		41A5047-2	Header bracket w/clevis pin & fastener
9		41A5034	Safety reversing sensor kit
			(receiving and sending eyes)
			with 3' (.9 m) 2-conductor bell wire
10		178B34	Straight door arm section
11		12B776	Hanging brackets
12		178B35	Curved door arm section
13		41A5266-1	Safety reversing sensor brackets (2)
			NOT SHOWN
		41A5258-11	Installation hardware bag
			(includes hardware listed on page 7)
		114A3667	Owner’s manual
		114A3667SP	Owner’s manual - Spanish

37

Contents

For Residential Use Only Introduction Assembly Adjustment Operation Installation Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Chain/Cable Tighten the Chain Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light and Lens Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER THE REMOTE CONTROL BATTERY LIMIT AND FORCE ADJUSTMENTS: MAINTENANCE SCHEDULE Once a Month HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: Repeat 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315MHz) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 953D 3-ButtonSECURITY✚® Remote Control : 956D www.chamberlain-diy.com CHAMBERLAIN® GARAGE DOOR OPENER ONE-YEARLIMITED WARRANTY FOUR-YEARMOTOR LIMITED WARRANTY