Care of Your Opener

LIMIT AND FORCE ADJUSTMENTS:

Weather conditions may cause some minor changes in door operation requiring some

readjustments, particularly

LIMIT CONTROLS

(Left side panel)

during the first year of operation.

 

Having a Problem?

1.The opener doesn't operate from either the Door Control or the remote control:

•

Does the opener have electric power? Plug a lamp

 

into the outlet. If it doesn't light, check the fuse box

 

or the circuit breaker. (Some outlets are controlled

 

by a wall switch.)

•

Have you disabled all door locks? Review

Pages 28 and 29 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully.

Repeat the safety reverse test (page 30) after any adjustment of limits or force.

MAINTENANCE SCHEDULE

9

 

1

9

1

7

3

 

7

3

 

5

 

 

5

 

KG

 

 

KG

 

 

 

Open Force

 

Close Force

FORCE CONTROLS (Back panel)

installation instruction warnings on page 11.

• Is there a build-up of ice or snow under the door?

The door may be frozen to the ground. Remove

any restriction.

• The garage door spring may be broken. Have it

replaced.

• Repeated operation may have tripped the

overload protector in the motor. Wait 15 minutes

Once a Month

•Manually operate door. If it is unbalanced or binding, call a trained door systems technician.

•Check to be sure door opens & closes fully. Adjust limits and/or force if necessary. (See pages 28 and 29.)

•Repeat the safety reverse test. Make any necessary adjustments. (See page 30.)

Twice a Year

•Check chain tension. Disconnect trolley first. Adjust if necessary (see page 11).

Once a Year

•Oil door rollers, bearings and hinges. The opener does not require additional lubrication. Do not grease the door tracks.

THE REMOTE CONTROL BATTERY

WARNING

To prevent possible SERIOUS INJURY or DEATH:

•NEVER allow small children near batteries.

•If battery swallowed, immediately notify doctor.

The lithium battery should produce power for up to 5 years. To replace battery, use the visor

clip or screwdriver blade to pry open the case as shown. Insert battery positive side up (+).

Dispose of old battery properly.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

and try again.

2.Opener operates from the remote, but not from the Door Control:

•Is the door control lit? If not, reverse the wires. If the opener runs, check for a faulty wire connection at the door control, a short under the staples, or a broken wire.

•Are the wiring connections correct? Review Installation Step 6, page 18.

3.The door operates from the Door Control, but not from the remote control:

•Is the door push bar flashing? If your model has the Lock feature, make sure it is off.

•Program the opener to match the remote control code. (Refer to instructions on the motor unit panel.) Repeat with all remotes.

4. The remote control has short range:

•Change the location of the remote control in your car.

•Check to be sure the antenna on the side or back panel of motor unit extends fully downward.

•Some installations may have shorter range due to a metal door, foil backed insulation, or metal garage siding.

5.Opener noise is disturbing in living quarters of home:

•If operational noise is a problem because of proximity of the opener to the living quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration to the house and is easy to install.

33