Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain PD432DM 1/2 HP NO, NO, NO, NO, KEY, KEY, PART, NOT SHOWN, NOT SHOWN, DESCRIPTION, DESCRIPTION, Installation Parts, Rail Assembly Parts

1 40

Download 40 pages, 2.56 Mb

REPAIR PARTS

	Rail Assembly Parts				1
					1
	2				8
	2				7
					7
	6
		KEY		PART
	5	NO.		NO.	DESCRIPTION
	5	1	81C275		Rack
		1	81C275		Rack
	4	2	41A6263		Hardware bag (includes
	3				sprocket coupling)
	3	3	12B890		Left rail bracket
		4	12B900		Right rail bracket
		5	41A6264		Screw drive rail assembly
					Complete 7' (2.1 m)
		6	12B889		Rail support brace
	Installation Parts	7	41A6262		Complete trolley assembly
	Installation Parts	8	41A4836		Drive sprocket kit
	4				NOT SHOWN
	1				NOT SHOWN
	1		28A143		Wire clips

LOCK

NOTICE

12

LIGHT	2
3
6	ONLY
	MOUNT
	CEILING
	UP
5	7
	7
10	11

9 8

13

KEY	PART
NO.	NO.	DESCRIPTION
1	41A5273-14	Multi-function door control
2	950D	1-Button remote control
3	10A20	3V 2032 Lithium battery
4	29B137	Visor clip
5	41A2828	Emergency release rope & handle assy.
6	41B4494-1	2-Conductor bell wire: white & white/red
7	41A4353	Header bracket w/clevis pin & fastener
8	41A5047	Door bracket w/clevis pin & fastener
9	41A5034	Safety sensor kit: receiving and sending eyes
		with 3' (.9 m) 2-conductor bell wire attached
10	178B34	Straight door arm section
11	12B776	Hanging bracket
12	178B35	Curved door arm section
13	41A5266-1	Safety sensor bracket
		NOT SHOWN
	41A4675-7	Installation hardware bag (see page 7)
	114A4320	Owner’s manual
	114A4320SP	Owner’s manual - Spanish

37

Contents

Page Introduction Assembly Installation Adjustment Operation Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail Assemble the Rail (continued) Fasten the Rail to the Motor Unit and Install the Trolley Attach the Rail Brackets Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Install The Protector System ® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY SENSORS Recommended Wire Routing Position the Opener Hang the Opener Install the Door Control Attach the Emergency Release Rope and Handle Electrical Requirements Complete the Safety Reversing Sensor Installation Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1. Assemble the door arm, Figure 5: 2.Adjustment procedures, Figure 6: •Closed door adjustment: decrease DOWN travel limit 3.Connect the door arm to the trolley: Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control THE MULTI-FUNCTIONDOOR CONTROL Light feature DISCONNECT THE TROLLEY: Lock feature LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY MAINTENANCE SCHEDULE Every Month Every Year 2. My remotes will not activate the door: 3.My door reverses for no apparent reason: 5.My lights will not turn off when door is open: Diagnostic Chart 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315 MHz) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts KEY NO DESCRIPTION Installation Parts Motor Unit Assembly Parts 953D 3-ButtonSECURITY✚® Remote Control : 935CB 940D OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIMPLY DIAL OUR TOLL FREE NUMBER: