OUTPUT RELAYS & CONFIGURATION SWITCH SETTINGS

Setting Output Relay Mode

The TriCode® receiver is factory set for momentary relay output “MNT”.

Momentary mode: The output relay will be on for .5 seconds before turning off.

Constant pressure mode: Output relay is continuously on while receiving matching/valid ID code from transmitter. The output relay will turn off immediately once receiver does not receive a matching/valid ID code from the transmitter (Figure 3).

NOTE: If constant pressure mode is desired, open front cover and move mode jumper from “MNT” to “CST” (Figure 2).

Figure 3

Setting the Configuration Switch

The TriCode® receiver is factory set for Linear/Delta-3TM.

Locate the configuration switch and set it to the desired RF mode of operation (Figures 2 and 3). Modes are as follows:

Linear/Delta-3TM:works with all “Linear/Delta-3TM transmitters transmitted at 310 MHz using 8-bits ID system.

MultiTM: works with all “Multi-CodeTM transmitters transmitted at 300 MHz using 10-bits ID system.

StanleyTM: works with all “StanleyTM radio” transmitters transmitted at 310 MHz using 10-bits ID system.

Figure 2

Configuration

 

 

 

Delta-3/ LinearTM

310 MHz

 

 

 

 

 

 

Multi-CodeTM

300 MHz

Switch

 

 

 

 

 

 

StanleyTM

310 MHz

 

 

 

 

 

 

 

 

 

 

 

 

 

Relay

 

 

 

 

 

Relay

 

Configuration

 

 

 

 

 

 

 

 

 

CH2-mode

 

 

 

CH1-mode

 

 

 

 

 

 

Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CST MNT

 

 

 

CST MNT

 

 

TM

 

CH1

 

 

 

 

 

 

 

 

 

 

 

CH2

 

Delta-3/Linear

 

MODE

 

 

 

 

 

 

 

 

 

 

 

MODE

 

Multi-CodeTM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

StanleyTM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LINEARTM

TM

MULTI

TM

STAN

CH1 CST MNT

CST MNT CH2

MODE

MODE

3