Typical spider webs inside burner

Ignitor Lighting

￿Do not lean over grill while lighting.

1.Open lid. Turn on gas at gas source.

2.Turn LEFT knob to IGNITE.

3. Push IGNITOR Button

rapidly to light. Be sure burner

lights and stays lit.

 

4.If burner does not light turn knob(s) to OFF, wait 5 minutes and try again.

5.Turn RIGHT knob to IGNITE to light other burner.

6.If IGNITOR does not work, follow match lighting instructions.

After Lighting: Turn knob to HIGH position for warm-up. Do not warm up grill with knobs on IGNITE. Knobs and handle will become uncomfortably hot if left in IGNITE positions.

Match Lighting

￿Do not lean over grill while lighting.

1.

Open lid. Turn on gas at gas source.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Place lit match into match lighting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

hole from outside grill bottom (as

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

shown).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Push in and turn RIGHT knob to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IGNITE. Be sure burner lights and

 

 

 

 

 

 

 

Match

 

stays lit.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

lighting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

hole is in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Light left burner by pushing LEFT

 

 

 

 

 

 

 

 

 

 

 

 

bottom

 

knob in and turning to

IGNITE.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or side

After Lighting: Turn Knob to HIGH for warm-up.

CAUTION

If burner does not light, turn knobs to OFF. Wait 5 minutes and try again. If the burner does not ignite with valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury.

Burner Flame Check

HIGH

• Light burner, rotate knobs

LOW

from HIGH to LOW. You

 

should see a smaller flame in

 

LOW position than seen on HIGH. Always check flame prior to each use. If only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section.

Turning Grill Off

• Turn all knobs to OFF position. Turn gas OFF at gas source.

Ignitor Check

Turn gas off at gas source. Press ignitor button rapidly. "Click" should be heard and spark seen each time between collector box or burner and electrode. See "Troubleshooting" if no click or spark.

Valve Check

Important: Make sure gas is OFF at gas source before checking valves. Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should spring back. If knobs do not spring back, replace valve assembly before using grill. Turn knobs to LOW position then turn back to OFF position. Valves should turn smoothly.

Hose Check

Before each use, check to see if hose is cut or worn. Replace damaged hoses before using grill. Use only valve and hose specified by manufacturer.

CAUTION

Clean burner prior to use after storing, at the beginning

of the grilling season or after a period of one month not being used. Spiders and insects

like to build nests in burner tubes (especially during colder months). These nests can cause fires in burner tubes or under grill.

See following pages for specific cleaning instructions.

General Grill Cleaning

Do not mistake brown or black accumulation of grease and smoke for paint. Interiors of gas grills are not painted at the factory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brush to insides of grill lid and bottom. Rinse and allow to completely air dry. Do not apply a caustic grill/oven cleaner to painted surfaces.

Plated wire grate: Wash grate and drip vaporiser bar with concentrated grill cleaner or use soap and water solution. Dry thoroughly and store indoors between cookouts.

Plastic parts: Wash with warm soapy water and wipe dry. ￿ Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.

Porcelain grate: Because of glass-like composition, most residue can be wiped away with baking soda/water solution or specially formulated cleaner. Use nonabrasive scouring powder for stubborn stains.

Stainless Steel: Wash with mild detergent or nonabrasive cleaner and warm soapy water, wipe dry with a soft nonabrasive cloth

Briquet grate: This grate will eventually decompose and weaken with use. Remove grate from grill and tap to loosen any scaling. Brush grate vigorously with a wire brush to remove any additional scaling, rust or residue.

4638220 • 13

Page 13
Image 13
Char-Broil 4638220 manual Ignitor Lighting, Burner Flame Check, Turning Grill Off, Ignitor Check, Valve Check, Hose Check